Question about Toyota ECHO

1 Answer

HOW TO FIND THE CAM SHAFT MARC ON A 2002 TOYOTA ECHO?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Toyota Expert
  • 276 Answers

They are usually on the sprocket sometimes an arrow or a circle. make sure the timing is on TDC when you replace it

Posted on Aug 26, 2018

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1779 Answers

SOURCE: I need to find the pattern for the serpentine belt on my 2002 toyota echo

Did you check under the hood? There should be a decal w/ the proper routing of the belt somewhere in or around the engine compartment. If u can't find it, let me know, I'll try to get more info. countrycurt0

Posted on Oct 11, 2008

  • 1 Answer

SOURCE: Fuses in a 2002 toyota echo?

The one labeled "ACC" in the interior fuse box

Posted on Jun 25, 2009

ZJLimited
  • 17970 Answers

SOURCE: 1996 toyota camry 2.2 5s- too manny timing marks crank shaft,cam shaft and cam shaft gears

Hi there:I dont have this diagram for 2S-ELC, 3S-FE and 5S-FE Engines, but pay attention at this...
To install:

  1. Align the cutouts of the oil pump pulley and shaft, and slide the pulley on. Retain the pulley while tightening the nut to 21 ft. lbs. (28 Nm).
  2. Align the crankshaft timing pulley set key with the key groove of the crankshaft pulley, then slide the pulley on.
  3. Install the No. 2 idler pulley with the bolt and tighten to 31 ft. lbs. (42 Nm). Be sure the pulley moves smoothly.

Remove any oil or water on the idler pulley and keep it clean.

  1. Temporarily install the No. 1 idler pulley with the retaining bolt. Hint: use a 1.65 inch (42mm) bolt in length. Do not tighten the bolt yet. Install the tension spring. Pry the pulley toward the left as far as it will go, then tighten the bolt.
  2. Turn the crankshaft until the key groove in the crankshaft timing pulley is facing upward. Install the timing belt on the crankshaft timing, oil pump, No. 2 idler and water pump pulleys.

If the old timing belt is being reinstalled, make sure the directional arrow is facing in the original direction and that the belt and crankshaft gear matchmarks are properly aligned.

  1. Install the lower (No. 1) timing belt cover and new gasket with the four bolts.
  2. Align the crankshaft pulley set key with the pulley key groove. Install the pulley. Tighten the pulley bolt to 80 ft. lbs. (108 Nm).
  3. On 2S-ELC engines, turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
  4. Align the camshaft knock pin with the matchmarks on the oil seal retainer.
  5. On 2S-ELC/USA engines, align the knock pin with the pin hole on the timing pulley E mark side. On 2S-ELC/Canadian engines, align the knock pin with the pin hole on the timing pulley. On 3S-FE and 5S-FE engines, align the knock pin with the groove of the pulley, and slide the pulley onto the camshaft with the plate washer and set bolt.

On 2S-ELC engines, make sure that the Matchmark on the oil seal retainer and center hole of the small hole on the camshaft timing pulley are aligned.

  1. Using the removal tool to hold the pulley stationary, install and tighten the pulley set bolt to 40 ft. lbs. (54 Nm) on the 2S-ELC and the 3S-FE. On the 5S-FE, tighten the set bolt to 27 ft. lbs. (37 Nm).
  2. On 3S-FE and 5S-FE engines, turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
  3. Install the timing belt and check the valve timing as follows:
    1. Align the matchmarks that you made previously, and install the timing belt onto the camshaft pulley.
    2. Loosen the No. 1 idler pulley set bolt 1 / 2 turn.
    3. Turn the crankshaft pulley two complete revolutions TDC to TDC. ALWAYS turn the crankshaft CLOCKWISE. Check that the pulleys are still in alignment with the timing marks.
    4. Tighten the No. 1 idler pulley set bolt to 31 ft. lbs. (42 Nm).
    5. Make sure there is belt tension between the crankshaft and camshaft timing pulleys.

  4. Install the upper (No. 2) timing cover with a new gasket(s). On the 5S-FE, align the two clamps for the engine wiring harness with the cover mounting bolts.
  5. Install the spark plugs.
  6. Install the right mounting insulator with bracket. Tighten the bracket bolts to 38 ft. lbs. (52 Nm), insulator nuts to 38 ft. lbs. (52 Nm) and thru-bolt to 52 ft. lbs. (71 Nm). On the 5S-FE, install the No. 2 engine mount bracket and tighten to 38 ft. lbs. (52 Nm); install the control rod and tighten the bolts to 47 ft. lbs. (64 Nm).
  7. Lower the engine.
  8. On 3S-FE and 5S-FE engines, install the alternator and alternator bracket. On 2S-ELC engines, install the power steering reservoir tank.
  9. Install the drive belt and adjust the tension.
  10. Install the cruise control actuator with bracket.
  11. Install the fender apron seal and right engine under cover.
  12. Install the right front wheel.


Hope this helps.

Posted on Jun 12, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota echo problem


run the fault codes to find the problem . Guessing and changing items just costs money and becomes frustrating. With the engine light on it could be more serious than plugs and coil

Jul 19, 2014 | 2002 Toyota ECHO

1 Answer

What type oil do i use in my 2005 toyota echo


Have you looked at your oil fill cap? It should tell you what type of oil to use. I have a 2002 Echo 1.5l and mine says 5w-30. I also have a 2005 Pontiac Vibe and it has a Toyota engine 1.8l that is slightly bigger than the 1.5lmotor in our Echo and it also takes 5w-30. I think you would be safe using 5w-30; however, I would look at your oil fill cap.

Jul 13, 2014 | 2002 Toyota ECHO

1 Answer

Timing chain


0c00d5b1-d5e1-45f3-9420-02d0d1bffc01.jpg is this the one

Jul 28, 2013 | 2000 Toyota ECHO

2 Answers

Video how to to change the blower fan on toyota Echo 2002


This blower fan in the 2002 Toyota Echo is located under the dashboard on the passenger side of the vehicle. It is covered by a plastic panel that snaps into place and shields the motor from accidental damage. When the blower fan fails, air will not come out of the vehicle's vents despite the fan control speed setting. A replacement blower motor can be purchased from a certified Toyota dealerships or any auto parts store
.


read more: obd2 car diagnostic

Aug 05, 2012 | 2002 Toyota ECHO

1 Answer

Check engine light Code P1725 for a Toyota echo 2001


That code is related to the automatic transmission, It is indicating that the Turbine Shaft Speed Sensor Circuit has Malfunctioned.

Possible causes

Input shaft speed sensor signal (NT) circuit is open or shorted Input shaft speed sensor is damaged or has failed PCM has failed

Feb 16, 2012 | 2001 Toyota Echo

1 Answer

2002 toyota echo replacing rear brake shoes now drums won't fit


I had a similiar problem with mine the hand brake was stuck on and wouldn't let the new drums go back on.

Jan 24, 2012 | 2000 Toyota ECHO

1 Answer

2000 toyota echo timing belt replacement


Hi. Toyota echo uses a chain drive cam. No timing belt

Aug 10, 2010 | 2000 Toyota ECHO

1 Answer

Fuses in a 2002 toyota echo?


The one labeled "ACC" in the interior fuse box

Apr 06, 2009 | 2002 Toyota ECHO

1 Answer

I need to find the pattern for the serpentine belt on my 2002 toyota echo


Did you check under the hood? There should be a decal w/ the proper routing of the belt somewhere in or around the engine compartment. If u can't find it, let me know, I'll try to get more info. countrycurt0

Oct 11, 2008 | 2002 Toyota ECHO

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...