Question about 1991 Mazda B-Series

Open Question

I have a 1991 mazda b2600i with a 159cui engine mad by mitsubishi and am trying to find the placement of the inerscha switch is

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
toneman2121
  • 775 Answers

SOURCE: Mazda B2600i

are there any fault codes present? i was looking at the fuel injection diagram on autozone.com and the only thing i can see that controls injector pulse width is the pcm. are all the injectors open for 15ms? you should also check fuel pressure. if you want to look at the diagram, go to autozone.com. register and enter you car. select repair guides, chassis electrical and the wiring diagrams

Posted on Mar 30, 2010

Ad
  • 7353 Answers

SOURCE: trying to find the fuel cutoff switch for 1989

There isnt one.

Posted on May 31, 2010

elshaddai159
  • 1016 Answers

SOURCE: 1991 Mazda B2600i power steering

Hi,
These sounds like the copper washer underneath the hose needs replacing or you just need to tighten the nut on the hose, check the washer and try to tighten it.
Hope this helps.
Thanks
Jason

Posted on Jan 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed my brakes on a 1991 Mazda b2600i


Take 2 people to do this. 1 person stays in the car and pumps the brakes then holds the pedal down. Starting at the P.R. tire, open the bleeder valve, once all the liquid and possible air stops coming out close the valve and have the other person pump the brakes and hold the pedal down again. Remember to keep the brake fluid filled up and do the brakes in this order: P.R., D.R., P.F., and finally D.F.

If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

May 03, 2015 | 1991 Mazda B-Series

1 Answer

Engine occasionally stalls while driving down the highway in my Mazda b2600i p/u like I turned the key off


Larry,
problem can be electrical or fuel system,
first of all check the ignition key switch and its relative wire harness for loose connection.
it can be happen because of fuel injection failure ,then go to the mechanic and you can rectify the problem.
regards,
nuwan

Jan 10, 2014 | 1989 Mazda B-Series

1 Answer

My 1991 Mazda b2600i doesn't seem to be getting


Have a fuel pressure test done on the fuel manifold to check for pump, filter and fuel regulator problems. Run fault codes to check for evap canister solenoid problems

Sep 14, 2013 | Cars & Trucks

1 Answer

1991 Mazda B2600i power steering fluid leaks at TOP of pump unit where hose from reservoir connects to it.


Hi,
These sounds like the copper washer underneath the hose needs replacing or you just need to tighten the nut on the hose, check the washer and try to tighten it.
Hope this helps.
Thanks
Jason

Jan 06, 2011 | Mazda B-Series Truck Cars & Trucks

1 Answer

Need ignition diagram for 1991 mazda b2600i 4x4 truck


Sorry my friend i would but that info can get me in alot of trouble. i would buy a shop manual for that vehicle.

Aug 24, 2010 | Mazda B2600 Cars & Trucks

1 Answer

Check engine light on; Gas milage went from 19 to 15, emission ba


YES!!, you had it tuned, it runs good, but gas mileage dropped, and check engine light is on,it sounds like the o2 sensors are slow or even dead, i would replace them for sure and that just might solve all your problems,good luck, hope this helps.

Apr 20, 2010 | 1991 Mazda B-Series

1 Answer

1991 Mazda truck starts, then dies unless


Not a solution but i am going through the exact same nightmare and same symptoms with my 1991 mazda b2200. I've apwnt over two grand to have my rebuilt TWICE and my alternator replaced and still does the same thing just starts only to die 2 seconds or so later unless i let it warm up to its max but will still die when taking turns and stopping at lights.

Mar 23, 2009 | 1991 Mazda B-Series

Not finding what you are looking for?
1991 Mazda B-Series Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...