Question about 2001 Volvo V40

Open Question

Can a bad Volvo EVAP Vapor Canister Purge Valve cause rough start?

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 133 Answers

SOURCE: I have a P0455 Evap code and so far 3 visits to

Check the charcoal canister

Posted on Feb 26, 2010

Ad
  • 2 Answers

SOURCE: Volvo S70 air control valve

where is the iac and the idle air control valve located on a volvo s70 1999

Posted on Sep 12, 2010

  • 1168 Answers

SOURCE: Where is the Charcoal canister

Hello cf2154.

Here is a diagram showing the location of the canister ahead of the right rear wheel well under the vehicle.
kiltylake_218.gif

The purge valve on most vehicles is under the hood. Purge opens when the vehicle is running under certain driving conditions to burn the stored vapors from the canister. Its usual position is closed.
If this valve fails to seal it will set a code for a leak failure. These valves are usually not the ones that fail the most.

The shut off valve on the other hand is normally open and closes only when the system runs a test to check the integrity of the system.
If this valve sticks closed it makes it hard to fill the fuel tank. Or if it sticks open the test will fail because it leaks.
Because they are more exposed to road debris and damage they are usually the ones that fail.

If you would like further assistance with this problem, please ask me here in a comment.
Thank you for using FixYa.
KL

Posted on Mar 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is purge valve located?


How to test and replace the EVAP Canister Purge Volume ...

? 13:49
https://www.youtube.com/watch?v=QnVUBYdFHGI
Mar 29, 2014 - Uploaded by CarsNToys
The EVAP canister purge control volume control valve is operated by a step motor for control of flow rate of fuel vapor fromEVAP canister.

How To Install Replace Vapor Canister Solenoid Purge ...

? 2:14
https://www.youtube.com/watch?v=TZ6ZB_acC9w
Sep 16, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/vapor-canister-purge-solenoid-valve-ac-delco- ... How To Test and Replace EVAP Canister Vent ControlValve P0446 ...

EVAP Purge Solenoid Removal - YouTube

? 4:24
https://www.youtube.com/watch?v=Xj605HENFno
Feb 26, 2008 - Uploaded by richpin06a
EVAP Purge Solenoid Removal Saturn S-series. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by ...


Dec 18, 2015 | Cars & Trucks

1 Answer

What code is po443


ossible causes
- Faulty Evaporative Emission (EVAP) Purge Solenoid Control
- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
- Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection
help.jpg What does this mean?
When is the code detected?
An improper voltage signal is sent to Engine Control Module (ECM) through the valve.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
P0443 Description
The Evaporative Emission System (EVAP) canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the Engine Control Module (ECM). The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.

Jul 21, 2014 | 2000 Mercury Mountaineer

1 Answer

P0446 ford escort 98


This Pinpoint Test is intended to diagnose the following:
  • Canister vent (CV) solenoid (9F945) (electrical concern only)
  • Fuel filler cap (9030)
  • Fuel tank pressure (FTP) sensor (9C052)
  • EVAP canister tube (fuel tank to EVAP canister)(9A228)
  • Fuel canister purge outlet tube (EVAP canister to EVAP canister purge valve) (9D661)
  • EVAP return tube (EVAP canister purge valve to intake manifold) (9G271)
  • EVAP canister purge valve (9C915)
  • Vacuum source line (input port vacuum to intake manifold)
  • Harness circuits: CV, FLI, FTP, EVAP Canister Purge Valve, SIG RTN, vehicle power (VPWR), reference voltage (VREF) and power ground (PWR GND)
  • Powertrain control module (PCM) (12A650)
This Pinpoint Test is used as an assistance in diagnosing the following EVAP components:
  • EVAP canister and bracket assembly (9E857)
    • EVAP canister sleeve assembly (fitting)(9D925)
    • Canister vent (CV) solenoid - hose assembly (9F976 or 9K318)
    • EVAP canister (9D653)
    • Canister vent (CV) solenoid (9F945)(mechanical concern only)
  • Fill limit valve assembly (9A086)
  • Fuel filler pipe flapper valve (9B085)
  • Fuel filler pipe check valve (9189), assembly (9285)
  • Fuel tank filler pipe (9034)
  • Fuel tank assembly (with fuel vapor vent valve) (9K007)
  • Fuel tank assembly (without fuel vapor vent valve) (9002)
  • Fuel vapor control valve (9B190)
  • Fuel vapor vent valve (9B593)
  • Liquid/vapor fuel discriminator (9G332)
  • On-board refueling vapor recovery (ORVR) T - connector assembly (9S314)
Description For additional information on the Evaporative Emission (EVAP) System, refer to Section 1A .
For additional information on the Evaporative Emission System Monitor, refer to Section 1A .
Pinpoint Test Schematics Escort/Tracer (2V)
aa3060b.gif

May 28, 2011 | 1998 Ford Escort

2 Answers

Check engine lite came on code is p1443 what does this code mean


P1443 Evaporative Emission Control System Control Valve The Evaporative Emission Control System monitors the fuel vapor flow between the engine intake manifold and the EVAP canister. The system failure occurs when a leak or blockage between the intake manifold, the EVAP canister purge valve and the EVAP canister is detected by the PCM.

Code P1443 Possible Causes:

- Pinched, blocked or plugged fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister

- Disconnected, cracked or cut fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister purge valve

May 04, 2011 | 1997 Ford Escort

2 Answers

P1444 Flujo de purga del circuito de entrada en q parte se encuentra localizada o localizado el senso r o valvula.nissan patfinder 98 motor 3.3


I don't know any Spanish but here is the codes definition.

P1444 - Purge Flow Sensor Circuit Low Input

The EVAP canister purge volume control solenoid valve uses a ON/ OFF duty to control the flow rate of fuel vapor from the EVAP canister.The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the ECM. The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.

Causes:
  • EVAP control system pressure sensor
  • EVAP canister purge volume control solenoid valve (The valve is stuck open.)
  • EVAP canister vent control valve
  • EVAP canister
  • Hoses (Hoses are connected incorrectly or clogged.)
  • Feb 02, 2011 | 1998 Nissan Pathfinder

    2 Answers

    Ford escort wagon 1997 code p1443 displayed. what does this indicate & where is the cannister? thank you.


    P1443 - EVAP Control System / Vacuum System Purge Control Solenoid Or Purge Control Valve Fault. A fuel tank pressure change greater than minus (-) 7 inches of water in 30 seconds occurred with a purge (fuel vapor) flow at less than 0.02 pounds per minute.

    Possible Causes:
  • Blocked fuel vapor hose between the EVAP canister purge valve and the FTP sensor.
  • Blocked fuel vapor hose between the EVAP canister purge valve and the engine intake manifold.
  • Blocked vacuum hose between the EVAP canister purge valve solenoid and the engine intake manifold.
  • EVAP canister purge valve stuck closed (mechanically).

  • Possible Solution:
    Check for blockages between the fuel tank, the EVAP canister purge valve, and the engine intake manifold. Check for obstructions in the EVAP canister purge valve diaphragm and ports.

    The canister is on the passengers side near the firewall if I recall correctly.

    Jan 18, 2011 | Ford Escort Cars & Trucks

    2 Answers

    Code says evaporator purge solenoid


    Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

    P0440 Evaporative emission (EVAP) system - malfunction

    Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


    P0441 Evaporative emission (EVAP) system - incorrect flow detected

    Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


    P0442 Evaporative emission (EVAP) system - small leak detected

    Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


    P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

    Possible causes: Wiring, EVAP canister purge valve, ECM


    P0444 Evaporative emission (EVAP) canister purge valve -open circuit

    Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


    P0445 Evaporative emission (EVAP) canister purge valve -short circuit

    Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


    P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

    Possible causes: Wiring, EVAP pressure sensor, ECM


    P0455 Evaporative emission (EVAP) system - large leak detected

    Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


    P0456 Evaporative emission system - very small leak detected

    Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


    P0457 Evaporative emission system - leak detected (fuel cap loose/off)

    Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


    P0458 Evaporative emission system, purge control valve -circuit low

    Possible causes: Wiring short to earth, EVAP valve


    P0459 Evaporative emission system, purge control valve -circuit high
    Possible causes: Wiring short to positive, EVAP valve


    Evaporative Emission Purge Solenoid

    Description & Operation
    The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
    During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
    The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
    Removal & Installation
    The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

    1. Disconnect electrical connector at solenoid.
    2. Disconnect vacuum lines at solenoid.
    3. Lift solenoid slot from mounting bracket for Removal & Installation.

    To Install:
    1. Position solenoid slot to mounting bracket.
    2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
    3. Connect electrical connector to solenoid.
    Purge solenoid location:

    jturcotte_65.gif
    EVAP cannister location:
    jturcotte_66.gif

    Nov 05, 2010 | 2000 Jeep Grand Cherokee

    1 Answer

    Obd-2 code p1455


    DTC P1455 - Substantial Leak or Blockage in Evaporative Emission Control System

    The PCM monitors the complete EVAP control system for no purge flow, the presence of a large fuel vapor leak or multiple small fuel vapor leaks. The system failure occurs when no purge flow (attributed to fuel vapor blockages or restrictions), a large fuel vapor leak or multiple fuel vapor leaks are detected by the EVAP running loss monitor test with the engine running (but not at idle).

    Check this possible causes:
    After-market EVAP hardware (such as fuel filler cap) non-conforming to required specifications
    Disconnected or cracked fuel EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube
    EVAP canister purge valve stuck closed
    Damaged EVAP canister
    Damaged or missing fuel filler cap
    Insufficient fuel filler cap installation
    Loose fuel vapor hose/tube connections to EVAP system components
    Blockages or restrictions in fuel vapor hoses/tubes (items also listed under disconnections or cracks)
    Fuel vapor control valve tube assembly or fuel vapor vent valve assembly blocked
    Canister vent (CV) solenoid stuck open
    Mechanically inoperative fuel tank pressure (FTP) sensor


    Check for audible vacuum noise or significant fuel odor in the engine compartment or near the EVAP canister and fuel tank

    Tell us news.

    Jul 19, 2010 | 1996 Ford Explorer

    2 Answers

    What is he code 455 for a 2006 hyundai sonata means


    CODE PO455 EVAPORATIVE EMISSION SYSTEM LARGE LEAK DETECTED.POSSIBLE CAUSES CANISTER VENT SOLENOID MAY BE STUCK IN OPEN POSITION / EVAP CANISTER TUBE EVAP CANISTER PURGE OUTLET TUBE OR EVAP RETURN TUBE DISCONNECTED OR CRACKED OR CANISTER IS DAMAGED / EVAP CANISTER PURGE VALVE STUCK CLOSED OR CANISTER DAMAGED / FUEL FILLER CAP MISSING LOOSE NOT TIGHT OR THE WRONG PART / FUEL VAPOR HOSES TUBES BLOCKED OR RESTRICED OR FUEL VAPOR CONTROL VALVE TUBE OR FUEL VAPOR VENT VALVE ASSEMBLY BLOCKED /FUEL TANK PRESSURE SENSOR HAS FAILED MECHANICAL FAULT /FUEL TANK CONTROL VALVE IS CONTAMINATED DAMAGED OR HAS FAILED.

    Oct 21, 2009 | 2006 Hyundai Sonata

    1 Answer

    Im getting a P0441 EVAP emission control system purge flow fault code on my 2002 dodge neon


    Here is what I could find for your code error as potential causes:
    After market parts and accessories nonconforming to the EVAP system specifications.
    Damaged, missing or improperly installed fuel filler cap.
    Blockage in fuel vapor hoses/tubes (EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube) in EVAP system.
    Disconnected or cracked fuel vapor hoses/tubes in EVAP system.
    EVAP canister purge valve stuck closed.
    Canister vent (CV) solenoid stuck open.
    Fuel tank pressure (FTP) sensor malfunction.
    EVAP canister leaking.
    Fuel vapor control valve tube assembly blocked.
    Fuel vapor vent valve assembly blocked.

    Obviously the gas cap would be the easiest and cheapest thing to fix.  Just make sure it is put on correctly and tight.  If it is not that, I would have to suggest to take it to a mechanic because the other problems on that list are not really DIY material.  Hopefully it is the gas cap and you can take care of it yourself.  Good luck.

    May 17, 2009 | 2002 Dodge Neon

    Not finding what you are looking for?
    2001 Volvo V40 Logo

    Related Topics:

    1,137 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Volvo Experts

    Marvin
    Marvin

    Level 3 Expert

    85111 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22484 Answers

    Jonah Oneal

    Level 3 Expert

    14092 Answers

    Are you a Volvo Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...