Question about 1998 Hyundai Elantra
Inspect the spark plugs. If they are wet, suspect the injectors may be leaking,
Posted on Jan 04, 2018
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: im getting a P0441 EVAP
P0441 : Evap. Emission System Incorrect Purge Flow
The evaporative emission control system prevents hydrocarbon (HC) vapors from the fuel tank from escaping into the atmosphere where they could form photochemical smog. Gasoline vapors are collected in the charcoal canister. The ECM controls the Purge Control Solenoid Valve (PCSV) to purge any collected vapors from the canister back to the engine for combustlon. This valve is actuated by the purge control signal from the PCM and controls fuel vapor from the canister to the intake manifold.
Possible Cause : ● Leakage on hose to PCSV ● Defective PCSV
Posted on Aug 10, 2008
hi from uk not sure if same as uk hyundai's but here goes ? if you remove wheel do you see two countersunk posi screws between studs that appear to hold rotor ?? if so then you will have to first remove the brake caliper assy by unbolting from the rear of caliper two 13 mm spanner/socket ? then you remove the two bolts that secure the carrier that the caliper bolts to 17 mm spanner/socket now you can remove the two contersunk screws then you may have to tap the rotor off the hub from rearuse a wire brush to clean up/away all rust/dust from caliper and carrier assys b4 refitting (take precautions from breathing dust) i assume you are fitting new pads ?? reassemble carrier then b4 fitting pads smear a light coating of copper grease on the rear of pad (metal side ) this prevents squealing on brakes then fully reassemble then b4 fitting wheel? bleed the brakee caliper a couple of pumps should expel dirty fluid then fit wheel carry out same proceedure on other brake assy as above fully then b4 you move car pump brake to ensure pedal is firm you will find that bleeding brakes will make pedal firmer as the old fluid becomes compressable due to heat/moisture absorbsion over time and heat from brakes is transferred to fluid via caliper piston understand?? that is why alway policy to bleed/flush brake fluid at least two yr interval this reduces spongy brake pedal hope this is all clear 4 you to follow best wishes for new year and hope you update on how you go on??
Posted on Jan 10, 2009
its real easy open trunk lid take rear sill off should just pop off then take trim panels each side then there are 4 bolts each side 10mm tkae bolts out firmly pull on tail lights they should come out and then reverse back
Posted on Jan 26, 2009
Can't say for sure but my car acted stupid for a year nobody could figure out what was wrong then it broke down on me halfway into a 350 mile trip. It was the timing belt all along!
Posted on Feb 05, 2009
You really need a test drive by a tech. Any shop should be able to do that and give you a firm (written) estimate. It might not be a big deal. Shop around if you need a rebuild, If you need one, ask about their warranty. Believe it or not, a good reference for a tranny shop is the Used Car Manager at the Hyundai dealership. Go in to ask him, not over the phone, and be nice. You're asking for a favor after all. Many dealers do a lot of their work outside the store for reasons of cost. It all depends on the dealership. One will, one won't. Ask.
Posted on Jun 11, 2009
Tips for a great answer:
Dec 30, 2013 | 2008 Hyundai Elantra
Jan 16, 2013 | 1996 Toyota Corolla
Jun 13, 2012 | Hyundai Cars & Trucks
Feb 05, 2011 | 2000 Hyundai Elantra
Mar 12, 2010 | 2001 Hyundai Elantra
Jan 07, 2010 | 2001 Hyundai Elantra
Mar 03, 2009 | 1998 Hyundai Elantra
Jan 26, 2009 | 2001 Hyundai Elantra
41 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: