Truck will be running fine, then all of a sudden it will completely shut off. After we wait a few minutes and pump the clutch and make sure it is all the way to the floor it will start, sometimes. Sometimes we have to wait till the next day. It has also just lost power almost completely and then when I gave it gas it kept running.
We want to recommend you our website https://ottofact.com/
Our service helps people to find the best low-interest financing and leasing offers.
All our clients get a discount.
You need the engine computer scanned for fault codes, i thank you have an ignition control problem like a module or distributor pickup coil issue. These parts whenthey fail should leave fault cdes so get them read.
Next, the check engine light will pause shortly followed by the second digit
of the trouble code. For example if the check engine light blinks once and
pauses followed by six blinks the trouble code number would be 16. If no code is
present the check engine light will stay one constantly. To restart code
gathering turn the ignition key to the "off" position, wait three minutes and
turn the ignition key back "on" again without starting the engine. Remove the
jumper wire once code gathering is complete. To clear code after the repairs
have been made remove the negative battery cable for one minute and
reconnect.
Toyota
Diagnostic Connector
Toyota Code Definition Table
Code 11 Momentary interruption in power supply to ECU (electronic control
unit or computer) up to 1991
Code 12 Engine revolution signal missing Code 13 Rpm signal to ecu missing
above 1000 rpm
Code 14 Igniter signal to ecu missing
Code 16 A/T control signal missing from ecu
Code 21 Main oxygen sensor signal fault
Code 22 Water temperature sensor circuit fault
Code 23 and 24 Intake air temperature signal fault
Code 25 Air/fuel ratio LEAN
Code 26 Air/fuel ratio RICH
Code 27 Sub-oxygen sensor signal or heater circuit fault
Code 28 No. 2 oxygen sensor/heater signal fault
Code 31 and 32 Air flow meter circuit or Vacuum sensor signal fault Code 34
and 36 Turbo-charging pressure signal fault
Code 35 Altitude compensation sensor signal fault
Code 41 Throttle position circuit fault
Code 42 Vehicle speed sensor circuit
Code 43 No starter signal to the ecu
Code 51 AC signal on; DL contact off (in transmission shifter with diagnostic
connector jumped)
Code 52, 53 and 55 Knock sensor fault Code 71 EGR system malfunction
Code 72 Fuel cut solenoid signal fault
Code 78 Fuel pump control signal fault
Code 81, 83, 84 and 85 TCM communication fault
SOURCE: crank no start
SOUNDS LIKE THE CRANK SENSOR POSS. AS I HAVE ONE HERE THAT I JUST DIAGNOSED FOR THE SAME THING WITH A SCAN TOOL WHEN WE FINALLY GOT IT NOT TO START. I'LL FOLLOW UP AFTER SENSOR INSTALL
SOURCE: truck starts, dies. truck runs good some days,bad the next
I had the same problem with My 1990 F150 300 6cylinder 4x4.....I cahnged all the same things you did, finally I sprayed a can of Gumout through the throttle body and it worked and ran great. Now I add fuel injector cleaner to the gas and a regular clean with the gumout and the problem has'nt come back. Good Luck to you and hope it works!
SOURCE: 92 Maxima Putters and sometimes even no gas sometimes
Yes I can help you. Change your coolant temperature sensor and all will be well. Only use Nissan, Bosch, or NGK part.
SOURCE: truck will idle but stalls when i try to give it gas
I do not know what engines yu guys have but this does sound like fuel starvation. Replace the fuel filters and go from there
Good Luck
SOURCE: When I start my 2000 GMC Sierra the gear shift
someone has cut the dash off you need to go to the information center and press menu it will give the options to cut it on or off
1,059 views
Usually answered in minutes!
×