Question about 1999 Chevrolet Blazer

2 Answers

How to remove rear bumper 1999 blazer - 1999 Chevrolet Blazer

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,970 Answers

Hi there:
Check this Removal Procedure...

how to remove rear bumper 1999 blazer - 6_23_2012_11_21_59_pm.gif

1. Remove the rear bumper step pads.
2. Remove the license plate lamps.
3. Remove the nuts and the bolts that retain the rear bumper impact bar to the bumper bracket.
4. Remove the rear bumper impact bar from the vehicle.

Installation Procedure

6_23_2012_11_22_56_pm.gif

Notice: Refer to Fastener Notice in Service Precautions.

1. Install the rear bumper impact bar to the vehicle as follows:

1.1. Position the bumper impact bar on the bumper brackets so that the holes in the impact bar are aligned with the bracket holes.
1.2. Install 2 bolt plates and 4 nuts on top of the impact bar.
1.3. Install 2 bolt and nuts through the bottom of the impact bar. Tighten the rear bumper impact bar nuts to 90 N.m (66 lb ft).

2. Install the license plate lamps.
3. Install the rear bumper step pads.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Jun 23, 2012

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 85,160 Answers

Go under the truck and remove the four to six bolts that hold it to the frame and into the wiring harness then careful lower the bumper down with a hydraulic floor jack.

Posted on Jun 23, 2012

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 99 Answers

SOURCE: Remove rear plastic bumper cover

please email me at meanness628@aim.com with any other info or questions if you have already gone to a body shop

Posted on Sep 29, 2008

  • 6982 Answers

SOURCE: Rear axle removal

Remove wheel, remove rear diff cover, remove small bolt that retains spider gear cross shaft in the carrier. Push axle in, remove "c" clip on end of axle and remove axle from housing. Reverse to replace. Only problem you may have is that sometimes small bolt is broken inside carrier. if broken you will need to drill a tiny hole into it and remove with tiny "easy out" or other similar device.
Do not turn carrier when shaft has been removed or spider gears will rotate and fall out!

Posted on Feb 24, 2009

thecoop27
  • 10 Answers

SOURCE: how do i remove a rear bumper from a audi a4

If I remember correctly, you just push forward and pull the side out, just like the front bumper.

Posted on Sep 15, 2009

  • 4793 Answers

SOURCE: Volkswagen Passat rear bumper removal

all the screws/bolts are underneath the plastic cover.hex head.(allen key)

Posted on Jul 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove a 93 Blazer Silverado rear bumper


Cut it off with a torch. Whether it is a blazer or silverado.

Oct 30, 2014 | Cars & Trucks

1 Answer

How to removing the rear bumper bar


Slide under the bumper and look on the back side of it. You will find the bolts that attach it to the body.

Aug 07, 2014 | 1999 Saab 9-5

1 Answer

Replace license plate light


With step bumper,
  1. Release the lamp's retainer from the rear bumper by pulling the lamp up and tilting the bottom of the lamp away from the bumper.
  2. Remove the lamp from the rear bumper by rotating it clockwise or counterclockwise

Oct 23, 2013 | 2001 Chevrolet Blazer

1 Answer

How to remove front bumper 1999 blazer


look behind bumper you'll see nuts near bumper brackets

Nov 06, 2012 | 1999 Chevrolet Blazer

1 Answer

Purge control solenoid. can't find this on my blazer. need to know what i am looking for. can the replacement part look different than the original?


The purge control solenoid is located behind the rear bumper on the drivers side it looks sort of like acan but is plastic and the solenoid is on top of it.

Apr 22, 2011 | 1999 Chevrolet Blazer

2 Answers

Wheres the oil filter?


I think on that year its behind the front bumper look in the plastic skid plate there should be a little door that opens with a flat screwdriver

Feb 01, 2011 | 1999 Chevrolet Blazer

1 Answer

How do I change the bumper on a 2000 Blazer


Front or rear, I am guessing it is the rear as they tend to get the most abuse and or rust! Start by removing the plastic step guard on the top of the bumper (use a flat ply bar) you will see the four bolts (remove those) and directly inline with those from the underside you will see four more (remove those) your bumper is free, there is one wire connector to release (licence plate lights) and simple lift off the bumper.

Dec 08, 2010 | 2000 Chevrolet Blazer

1 Answer

Volkswagen Passat rear bumper removal


all the screws/bolts are underneath the plastic cover.hex head.(allen key)

Jul 11, 2010 | 1999 Volkswagen Passat

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

1 Answer

Replacing tag light


You probably figured this out by now, but in case you haven't... Reach up behind the rear bumper, rotate the bulb holder counterclockwise, then withdraw the holder from the housing and pull the bulb out. In some instances, the license light housing is held to the bumper with clips, and if you have a step on the bumper the housing is removed by pulling the housing upwards while pulling out at the bottom.

Aug 30, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

1,779 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...