Take a/c off motor - 1994 Chevrolet K1500

Which system ?
HVAC Systems - Manual HVAC Systems - Automatic
If automatic it's probably the blower motor control processor .
Blower Motor Control Processor The blower motor control processor is an interface between the HVAC control module and the blower motor. The blower motor speed control, Blower motor speed signal, battery positive voltage and ground circuits enable the control processor to operate. The HVAC control module sends the commanded blower motor speed to the control processor through a 0 to 12-volt linear ramped blower motor speed control circuit. As the blower motor speed control voltage increases, the blower motor speed increases. The control processor sends the actual blower speed to the control module through a 0 to 12-volt blower motor speed signal circuit. The processor supplies 12volts to the blower motor through the blower motor voltage supply circuit. The control processor uses the blower motor ground as a low side control to adjust the blower motor speed.

This vehicle doesn't have a blower motor resistor ! It has a blower motor control module , if you have automatic climate control !
If manual climate control , then there is a blower motor resistor assembly !
Blower Motor Control Processor The blower motor control processor controls the speed of the blower motor by increasing or decreasing the voltage drop on the ground side of the blower motor. The HVAC control module provides a low side pulse width modulated signal to the blower motor control processor over the blower motor speed control circuit. As the requested blower speed increases, the HVAC control module increases the amount of time that the speed signal is modulated to ground. As the requested blower speed decreases, the HVAC control module decreases the amount of time that the signal is modulated to ground.
Air Speed - Front Control
The blower motor forces outside air into the vehicle's interior. The vehicle operator determines the blower motor's speed when the driver places the blower switch in one of 5 blower speeds. The blower motor will always operate in any switch position other than OFF, as long as the ignition switch is in the RUN position. The blower motor and mode switches are located within the HVAC control module. The blower motor OFF input is connected in series with the HVAC control module by the off blower motor control circuit.
Depending upon the selected speed, power is provided to the blower motor from either the ignition 3 voltage or battery positive voltage circuits from the fuse block. The battery positive voltage circuit only provides power when the High blower switch position is selected. Power and ground are provided to the HVAC control module by the ignition 3 voltage and the ground circuits.
Low Blower Speed When the Low 1 blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the low blower motor control circuit. Voltage is divided between 4 series resistors, a blower relay, and the blower motor to achieve the desired blower speed. The blower motor is grounded through the ground circuit.
Medium Blower Speeds When the Medium 1 blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the medium 1 blower motor control circuit. Voltage is divided between 3 series resistors, a blower relay, and the blower motor to achieve the desired blower speed. The blower motor is grounded through the ground circuit.
When the Medium 2 blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the medium 2 blower motor control circuit. Voltage is divided between 2 series resistors, a blower relay, and the blower motor to achieve the desired blower speed. The blower motor is grounded through the ground circuit.
When the Medium 3 blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the medium 3 blower motor control circuit. Voltage is divided between a series resistor, a blower relay, and the blower motor to achieve the desired blower speed. The blower motor is grounded through the ground circuit.
High Blower Speed When the High blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the high blower motor control circuit. The voltage energizes the blower relay, causing the blower motor to be connected directly to the battery positive voltage circuit. The blower motor and blower motor relay are grounded through the ground circuit.
Go on you tube an check out videos on trouble shooting blower motor circuit
Chevy Trailblazer EXT Blower Motor Won Turn Off

With Delphi Blower Motor

1. If equipped, remove the sound insulator panel.
2. Remove the blower motor insulating cover screws.
3. Disconnect the electrical connector from the blower motor.
4. Remove the blower motor insulating cover.
5. Pull the retaining tab down while turning the blower motor counterclockwise in order to disengage the blower motor from the heater/ventilation module.
6. Remove the blower motor.

With Visteon Blower Motor

1. Remove the sound insulator panel.
2. Disconnect the electrical connector from the blower motor.
3. Remove the screws from the blower motor.
4. Remove the blower motor from the HVAC module.
5. Remove the retainer from the blower motor wheel. Discard the retainer.
6. Remove the blower motor wheel from the blower motor.

Blower Motor Removal & Installation W/O Air Conditioning Blower Motor (W/O Air Conditioning)

To Remove:

1. Remove the PCM.
2. Remove the coolant reservoir.
3. Remove the rear coolant recovery reservoir mounting stud.
4. Disconnect the cooling tube from the blower motor.
5. Disconnect the electrical connector from the blower motor.
6. Remove the blower motor mounting bolts.
7. Remove the blower motor insulating cover.
8. Remove the blower motor.

To Install:

1. Install the blower motor.
2. Install the blower motor mounting bolts.
3. Connect the electrical connector to the blower motor.
4. Connect the cooling tube to the blower motor.
5. Install the rear coolant recovery reservoir mounting stud.
6. Install the coolant reservoir.
7. Install the PCM.

W/ Air Conditioning Blower Motor (W/ Air Conditioning)

To Remove:

1. Remove the PCM.
2. Remove the coolant reservoir.
3. Remove the rear coolant recovery reservoir mounting stud.
4. Disconnect the electrical connector from the blower motor.
5. Move the PCM connectors out of the way.
6. Remove the blower motor access cover screws. CAUTION
   Do not cut any deeper than necessary in order to remove the access cover.
   
7. Cut through the access cover on the cut line using a sharp utility knife.
8. Disconnect the cooling tube from the blower motor.
9. Remove the blower motor mounting bolts.
10. Remove the blower motor.

To Install:

1. Install the blower motor.
2. Install the blower motor mounting bolts.
3. Connect the cooling tube to the blower motor.
4. Install the blower motor access cover.
5. Install the blower motor access cover retaining screws.
6. Using black weather-strip adhesive, seal the cut line.
7. Connect the blower motor electrical connector.
8. Reposition the PCM connectors.
9. Install the rear coolant recovery reservoir mounting stud.
10. Install the coolant reservoir.
11. Install the PCM.

Blower Motor Removal & Installation W/O Air Conditioning Blower Motor (W/O Air Conditioning)

To Remove:

1. Remove the PCM.
2. Remove the coolant reservoir.
3. Remove the rear coolant recovery reservoir mounting stud.
4. Disconnect the cooling tube from the blower motor.
5. Disconnect the electrical connector from the blower motor.
6. Remove the blower motor mounting bolts.
7. Remove the blower motor insulating cover.
8. Remove the blower motor.

To Install:

1. Install the blower motor.
2. Install the blower motor mounting bolts.
3. Connect the electrical connector to the blower motor.
4. Connect the cooling tube to the blower motor.
5. Install the rear coolant recovery reservoir mounting stud.
6. Install the coolant reservoir.
7. Install the PCM.

W/ Air Conditioning Blower Motor (W/ Air Conditioning)

To Remove:

1. Remove the PCM.
2. Remove the coolant reservoir.
3. Remove the rear coolant recovery reservoir mounting stud.
4. Disconnect the electrical connector from the blower motor.
5. Move the PCM connectors out of the way.
6. Remove the blower motor access cover screws. CAUTION
   Do not cut any deeper than necessary in order to remove the access cover.
   
7. Cut through the access cover on the cut line using a sharp utility knife.
8. Disconnect the cooling tube from the blower motor.
9. Remove the blower motor mounting bolts.
10. Remove the blower motor.

To Install:

1. Install the blower motor.
2. Install the blower motor mounting bolts.
3. Connect the cooling tube to the blower motor.
4. Install the blower motor access cover.
5. Install the blower motor access cover retaining screws.
6. Using black weather-strip adhesive, seal the cut line.
7. Connect the blower motor electrical connector.
8. Reposition the PCM connectors.
9. Install the rear coolant recovery reservoir mounting stud.
10. Install the coolant reservoir.
11. Install the PCM.

Wiper Motor

Removal & Installation

1. Disconnect the negative battery cable.
2. Disconnect the wiper motor electrical connector.
3. Remove the four mounting bolts securing the motor to the firewall.
4. Using a suitable prybar, carefully separate the wiper motor from the wiper linkage and remove the motor.

To install:

1. Attach the wiper motor ball joint to the wiper linkage.
2. Position the motor on the firewall and secure the motor with the four mounting bolts. Tighten the mounting bolts to 75 ft. lbs. (102 Nm).
3. Connect the electrical connector.
4. Connect the negative battery cable.

Removal

1. Remove the glove compartment liner to gain access to the heater blower motor and blower motor wheel assembly mounting screws.
   

1. Use a small screwdriver to remove clip retaining hydraulic damper strut.
   

1. Remove four screws and remove the heater blower motor assembly and blower motor wheel assembly from the heater blower motor housing.
   

Installation

1. Using a new seal, position the heater blower motor and blower motor wheel assembly to the heater blower motor housing with the flat side of the flange near the heater blower motor switch resistor (18591). Install the four retaining screws.
   

1. Tape the heater blower motor power lead to the air inlet duct to keep the wire away from the blower outlet during installation.
   

1. Install the heater blower motor and blower motor wheel assembly in the vehicle.
   

1. Install the glove compartment liner.
   

Blower Motor - REMOVAL & INSTALLATION
(see Figures 1 and 2)



Fig. 1: Exploded view of the blower motor mounting



Fig. 2: Exploded view of the blower motor and wheel (fan) assembly

Without Air Conditioning

1. Disconnect the negative battery cable.
2. Remove the air cleaner or air inlet duct, as necessary.
3. If necessary, Remove the speed control module and the washer fluid reservoir.
   

Fig. 3: To remove the blower motor, first disconnect the electrical wire harness plug...



Fig. 4: ...then remove the blower motor cooling tube from the motor

1. Disconnect the wire harness connector from the blower motor by pushing down on the connector tabs and pulling the connector off of the motor.
2. Disconnect the blower motor cooling tube at the blower motor.

Fig. 5: Remove the blower motor attaching screws and the washer fluid reservoir...



Fig. 6: ...then slide the blower motor from the housing. Take care to not damage the blower wheel (arrow)

1. Remove the 2 screws attaching the blower motor and wheel to the heater blower assembly.
2. Holding the cooling tube aside, pull the blower motor and wheel from the heater blower assembly and remove it from the vehicle.
3. Remove the blower wheel push-nut and/or clamp from the motor shaft and pull the blower wheel from the motor shaft.
   

To install:

1. Install the blower wheel on the blower motor shaft.
2. Install the hub clamp and/or push-nut.
3. Holding the cooling tube aside, position the blower motor and wheel on the heater blower assembly and install the 2 attaching screws.
4. Connect the blower motor cooling tube and the wire harness connector.
5. Install the vacuum reservoir on the hoses with the 1 screws.
6. If removed, install the speed control module and the washer fluid reservoir.
7. Install the air cleaner or air inlet duct, as necessary.
8. Connect the negative battery cable and check the system for proper operation.
   

With Air Conditioning

1. Disconnect the negative battery cable.
2. In the engine compartment, disconnect the wire harness from the motor by pushing down on the tab while pulling the connection off at the motor.
3. Remove the air cleaner or air inlet duct, as necessary.
4. If necessary, remove the solenoid box cover retaining bolts and the solenoid box cover.
5. Disconnect the blower motor cooling tube from the blower motor.
6. Remove the blower motor mounting plate attaching screws and remove the motor and wheel assembly from the evaporator assembly blower motor housing.
7. Remove the blower motor hub clamp from the motor shaft and pull the blower wheel from the shaft.
   

To install:

1. Install the blower motor wheel on the blower motor shaft and install a new hub clamp.
2. Install a new motor mounting seal on the blower housing before installing the blower motor.
3. Position the blower motor and wheel assembly in the blower housing and install the attaching screws.
4. Connect the blower motor cooling tube.
5. Connect the electrical wire harness hard shell connector to the blower motor by pushing into place.
6. If removed, position the solenoid box cover into place and install the 2 retaining screws.
7. Install the air cleaner or air inlet duct, as necessary.
8. Connect the negative battery cable and check the blower motor in all speeds for proper operation.

Hope this help (remember comment and rated this).

Blower Motor Removal & Installation Delphi
Blower Motor Replacement (Delphi)


To Remove:

1. Remove the instrument panel sound insulator panel (if equipped).
2. Disconnect the electrical connector from the blower motor.
3. Remove the blower motor insulating cover screws.
4. Remove the blower motor insulating cover.
5. Pull the retaining tab down and rotate blower motor counterclockwise to remove.

To Install:

1. Position the blower motor and turn assembly clockwise until tab locks in place.
2. Install the blower motor insulating cover.
3. Connect the electrical connector to the blower motor.
4. Install the instrument panel sound insulator panel (if equipped).

Visteon

Blower Motor Replacement (Visteon)


To Remove:

1. Remove the instrument panel sound insulator panel (if equipped).
2. Disconnect the electrical connector from the blower motor.
3. Remove the blower motor screws.
4. Remove the blower motor from the HVAC module.

To Install:

1. Position the blower motor and install mounting screws.
2. Connect the electrical connector to the blower motor.
3. Install the instrument panel sound insulator panel (if equipped).