does it have a digital control panel? As this uses an electronic blower speed controller located at the engine compartment (rear engine block) fix on ac phlenum try to shake the connector or wire while the system is on.
No, you don't have to pull the whole dash board but you have to pull a few panels....here is the steps on how to get to it and remove and replace it:
Disconnect the negative battery cable.
Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.
CAUTION
NEVER open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.
Plenum removal—1990-98 vehicles
Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
Remove the right and left lower instrument panel insulators.
On 1989 vehicles:
Remove the 3 glove compartment hinge screws, disconnect the check arms and remove the glove compartment.
Loosen the right door sill plate and remove the right side cowl trim panel.
Remove the bolt attaching the lower right end of the instrument panel to the side cowl.
Remove the instrument panel pad as follows:
Remove the 2 screws attaching the pad to the instrument panel at each defroster opening. Be careful not to drop the screws into the defroster openings.
Remove the one screw attaching each outboard end of the pad to the instrument panel.
On Crown Victoria, remove one pad attaching screw near the upper right corner of the glove compartment door.
Remove the 5 screws attaching the lower edge of the pad to the instrument panel. Pull the instrument panel pad rearward and remove it from the vehicle.
On 1990-98 vehicles:
Remove all instrument panel mounting screws and pull the instrument panel back as far as it will go without disconnecting any wiring harnesses.
Make sure the nuts attaching the instrument panel braces to the dash panel are removed.
Loosen the right door sill plate and remove the right side cowl trim panel.
If equipped with manual air conditioning, disengage the temperature control cable housing from the bracket on top of the plenum. Disconnect the cable from the temperature blend door crank arm.
If equipped with Automatic Temperature Control (ATC), proceed as follows:
On 1989 vehicles, disconnect the temperature control cable from the ATC sensor.
Detach the vacuum harness line connector from the ATC sensor harness and detach the electrical connector from the ATC servo connector.
On 1990-98 vehicles, remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator. Detach the ATC sensor tube from the evaporator case connector.
Detach the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct.
Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.
Floor air distribution duct removal—1990-98 vehicles
Remove the 2 hush panels.
Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum.
Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
Remove the 2 nuts from the 2 studs along the lower flange of the plenum.
Heater core removal—1990-98 vehicles
Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
On 1989 vehicles with ATC, remove the ATC servo from the plenum.
Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly.
Pull the heater core and seal assembly from the plenum assembly.
To install:
Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
On 1989 vehicles with ATC, install the ATC servo on the plenum.
Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
Connect the white vacuum hose to the outside-recirculating door vacuum motor. Attach the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
If equipped with ATC, proceed as follows:
On 1989 vehicles, connect the temperature control cable to the ATC sensor and adjust the cable. Route and attach the vacuum harness connector to the ATC sensor and attach the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
On 1990-98 vehicles, attach the ATC sensor tube to the evaporator case connector. Install the cross body brace and connect the wiring harness to the blend door actuator.
Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
On 1989 vehicles, install the instrument panel pad and the glove compartment door. On 1990-98 vehicles, push the instrument panel back into position and install all instrument panel mounting screws. Install the right and left lower instrument panel insulators.
Connect the vacuum supply hose(s) to the vacuum source.
Install the right and left lower instrument panel insulators and install the 2 hush panels.
Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
Connect the negative battery cable and check the system for proper operation.
2000 Ford Crown Victoria Car Radio Stereo Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Violet/Light Blue Car Radio Accessory Switched 12v+ Wire: Yellow/Black Car Radio Ground Wire: Black/Light Green Car Radio Illumination Wire: Light Blue/Red Car Stereo Antenna Trigger: Blue Left Front Speaker Positive Wire (+): Orange/Light Green Left Front Speaker Negative Wire (-): Light Blue/White Right Front Speaker Positive Wire (+): White/Light Green Right Front Speaker Negative Wire (-): Dark Green/Orange Left Rear Speaker Positive Wire (+): Gray/Light Blue Left Rear Speaker Negative Wire (-): Tan/Yellow Right Rear Speaker Positive Wire (+): Orange/Red Right Rear Speaker Negative Wire (-): Brown/Pink
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
No idea sounds like a multiplug connection ?? but i have no idea other than this ,now if it was a renault i would know that pluging it in would be a waste of time to start with as its all encrypted software for dealers only but a ford ?? never so look for a broken wiring connector
Check the connections, it could be a loose connection. Start the car and leave it running...put your hand under the dashboard on driver side, and wiggle any wire cable while watching the dash gages. Once you see it, then you know it.
if ur looking for chime alert then at fuse panel is a round plastic chime that may be disconnected or needs replacement--if your looking for dash light then possible light is burnt or wiring problem under dash--
Also check to see if there is power in the start wire form the ignition switch, the wire is a white wire with pink stripe, most likely not a common problem, but still something that could go wrong. this wire will feed the starter relay under the hood...
×