I Replaced the front wiper motor on my 2005 Equinox and the wipers stop in the up position how can I fix this

There's a switch on the motor; when you turn it off, it's going to continue till the wipers are in the "park" position. Possibly a ca or internal cam or detent activates a switch to stop rotating. You might need a new wiper motor if the position switch isn't external.

Sounds like the switch in the wiper motor has gone bad. You would have to replace the wiper motor to fix this problem. There are contacts inside the wiper motor head, when you turn them off it supplies power until the wipers return to the resting position and it opens the contact and then they stop. I hope you find this useful and helps you solve your issue.

Sorry , no adjustment .
Wiper/Washer System Components
The Wiper / Washer System consists of the following components:
• Windshield wiper / washer switch
• Windshield wiper system module / motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR 25A fuse
Wiper / Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls the wiper motor operation. The windshield wiper motor is a 2 speed motor. Windshield wiper DELAY operation is a low speed wiper motor function with a variable delay interval between the wipe cycles. The DELAY interval is controlled through a series of resistors within the wiper / washer switch.
Park Position Operation
When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Do you know how to do diagnostic's ?

Wipers Blades Do Not Park
Step
Action
Yes
No
Schematic Reference: Wiper/Washer Schematics
Connector End View Reference: Wiper/Washer Connector End Views
DEFINITION: This table diagnoses the wipers operate normally but will not return to the park position when the wiper operation is cancelled.
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Turn ON the ignition, with the engine OFF.
Move the wiper switch to the LO position.
Move the wiper switch to the OFF position.
Do the front wipers advance to the park position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn the ignition switch to the RUN position.
Turn the wiper switch to OFF.
Disconnect the wiper/washer switch connector.
Do the wipers park?
YES - Go to Step 7
NO - Go to Step 4
4
At the wiper/washer switch connector, measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 5
NO - Go to Step 8
5
Reconnect the wiper/washer switch connector.
Disconnect the wiper motor connector.
Measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 6
NO - Go to Step 8
6
Repair a short to battery positive voltage in the windshield wiper switch signal 2 circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
YES - Did you find and correct the condition?
NO - Go to Step 9
--
7
Replace the wiper/washer switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column - Tilt.
YES - Did you complete the replacement?
NO - Go to Step 9
--
8
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
YES - Did you complete the replacement?
NO - Go to Step 9
--
9
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Try to replace the fuse for it. Was it a GM motor or an aftermarket motor you put in?

try this fix
remove wiper arms from where they connect on car
turn wiper moter on then off. turn ignition off
if wiper motor is good it should put spline in off position and now all you need to do is replace wiper arms in the correct position they would be in when wipers are turned off

possibly the circuit board in the wiper motor has weak circuit.

Hey there. I had a similar problem on my 2001 galaxy diesel. On research it's a very common problem. If you are mechanically minded it can be an easy fix with a bit of time. You need to remove the whole wiper linkage and motor and free out the bushes that hold the wipers in position applying pbc grease before refitting. Continued use will only result in your motor burning out which is 350+euro from ford and if the linkage seizes completely then another 400+euro so catch it before it's too late.

Define gave out for me please

there is a fuse for the wipers that has a relay for when the wiper motor heats up like from heavy snow and it can cause some problems so check it or get a good mechanic to look at your position.

The 23 should work on the drivers side but you will need a 19" on the passenger side.
Hope this helps and let me know.
Regards,