Replace crankshaft position sensor
SOURCE: crankshaft position sensor location
Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.
SOURCE: CANNOT FIND THE CRANKSHAFT POSITION SENSOR
cerebral_eni: The crank position sensor is located at the back of the engine block just below the cylinder head. It actually projects into the bell housing and reads the teeth on the flywheel where it references TDC for #1 cyl and RPM's of the crank. It's a "Hall effects generator". Unless you are into electronics and have a lab scope to look for a square wave pattern, I will continue with my other input.
Nissan has a recall campaign on the crank angle sensors.
The campaign # is 07V527000:ECM update for stalling;
NHTSA07V527000 NOV 07,
The symptom was brief malfunction of sensor causing the engine to quit running which could potentially put the vehicle at risk for a collision. The sensors would ultimately fail. There was also a voluntary recall on the reprogramming of the ECM's due to stalling problems. TSB# NTB07-081, Campaign ID#R0712
I hope this information is of some assistance to you. You may be able you get your car repaired under warranty! Good Luck!
SOURCE: Crankshaft Position Sensor
the dual crankshaft position sensor is secured in an aluminum mounting bracket and bolted to the left side of the timing chain cover, partially behind the crankshaft balancer, hope this helps get back to me if you need mre help. please rate my fix as i strive to be the best
SOURCE: location of crankshaft position sensor Jeep grand cherokee 1997
left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,
SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?
it is located on the right side of the motor, in the trans area. Actually in the bell housing.
?€¢
Engine control module (ECM) replacement
?€¢
Crankshaft damper replacement
?€¢
Crankshaft replacement
?€¢
CKP sensor replacement
?€¢
Any engine repairs which disturb the crankshaft to CKP sensor relationship
Important: The scan tool monitors certain component signals to determine if all the conditions are met to continue with the CKP system variation learn procedure. The scan tool only displays the condition that inhibits the procedure. The scan tool monitors the following components:
?€¢
CKP sensor activity--If there is a CKP sensor condition, refer to the applicable DTC that set.
?€¢
Camshaft position (CMP) signal activity--If there is a CMP signal condition, refer to the applicable DTC that set.
?€¢
Engine coolant temperature (ECT)--If the engine coolant temperature is not warm enough, idle the engine until the engine coolant temperature reaches the correct temperature.
•
How to test Crankshaft Position CKP Sensor?
---------------
Crankshaft Position Sensor Operation?
----------------
Replace Camshaft position sensor and Crankshaft Position Sensor?
http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
----------
GMC Crankshaft Position (CKP) Sensor
Replacing?
http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html
------------
These details will help.
Thanks.
386 views
Usually answered in minutes!
×