Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on Nov 20, 2017

Trouble shooting astrostart remote starter for hst 5224 model

Truck wont start with remote starter or manually with key.it seems to be stuck in a security mode which will not allow truck to start.there is power to everything,the lights go on like it would when it goes into start mode except it will not start.it will not even engage the starter with either remote or the key.what can i do?

1 Answer

Floyd Tubbs

Level 1:

An expert who has achieved level 1.

MVP:

An expert that got 5 achievements.

New Friend:

An expert that has 1 follower.

Night Owl:

An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Contributor 20 Answers
  • Posted on Nov 20, 2017
Floyd Tubbs
Contributor
Level 1:

An expert who has achieved level 1.

MVP:

An expert that got 5 achievements.

New Friend:

An expert that has 1 follower.

Night Owl:

An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

Joined: May 14, 2015
Answers
20
Questions
0
Helped
7157
Points
55

Leave the ignition key on for 10 minutes until the security light goes off. You may have to do this three times for a 30-minute total for a relearn procedure

5 Related Answers

Anonymous

  • 574 Answers
  • Posted on Aug 23, 2009

SOURCE: security light blinks on dash , truck wont even try to start

Does your key have a chip on it? If it does its probably the problem

Ad

Anonymous

  • 1959 Answers
  • Posted on Sep 23, 2009

SOURCE: 87 seville wont start everything is powered,

Your car is equipped with the VATS security system. Cars with this system need a key with a "chip" in it to start the car. A regular key won't start the car because of the security system. A key from the dealership is needed to start any GM car with the VATS system.

jamie

  • 1810 Answers
  • Posted on Jan 03, 2010

SOURCE: Won't start or even turn over. Not a security or

sounds like a bad conection or a bad ground look arround the starter shake the wires while somone trys to start the car
since it is gm it is probably a fuseable link that has bit the dust

Anonymous

  • 6982 Answers
  • Posted on Jul 31, 2011

SOURCE: have 2006 chevy 3500. 6.0

Being started that many times per day, chances are that bushings are worn as are all the internal components. You could rebuild it but to do that correctly likely the parts would cost you more than a completely rebuilt unit. A good rebuild includes new end bushings, brushes, solenoid and bendix drive. The only original parts should be the housing, field coils and armature. The symptoms you posted sound more like a worn brush or solenoid internal contact. When testing voltages, your radio and lights are not a really good indicator of battery condition or charging system operation. Always use a good volt or multi-meter to do testing.

Anonymous

  • 15 Answers
  • Posted on Sep 24, 2011

SOURCE: truck has electrical power but

Safety first!--Make sure you're in park & brake on-- Try shorting across the starter terminals with a screwdriver,if the bendix kicks in & nothing spins,remove the starter & put in bench vice ,(or hold down securely), & jump with cables.--REMEMBER POLARITY--If the starter spins you are in deep *******---something in the motor is probably locked up.(If the starter doesn't spin get a new one.)

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Will this battery work in my astrostart HST 5225 remote? I bought a RRS 5225 it plugged in but full charge it worked but didn't last a day. did I just get a dud?

REMOTE START, CRAZY ADD ON.
WHY NOT ASK THEM FOR SUPPORT.
MY GUESS IS WRONG BATTERY.
WHAT MEANS RRS? A HUGE TYPO FOR RSS???????? WOW IF TRUE.

https://www.astrostart.com/Products/RemoteStartSecurity/4306/RSS-5225.aspx






i READ THE MANUAL THERE RSS5225
IT SAYS CLEAR AS DAY THIS.

:Your remote is powered by an internal rechargeable battery that can only be serviced by an authorized Directed dealeR"

READ THIS? PAGES ON CHARGING IT

https://www.directeddealers.com/manuals/OG/AstroStart/RSS-5225_OG-Eng-2.pdf

PAGE 7 CHARGING WITH USB

THE FOB IS 13 YEARS OLD RIGHT.
AND NO BATTERY LASTS FOR 13YEARS, AND MUST BE REPLACED
SO PULL IT OUT AND POST PART NUMBERS ON IT.
0helpful
1answer

I have a 2019 Nissan Sentra with an Astrostart DS4 that keeps getting a code 3 and the light on my dash for key comes on. Has anyone run into this?

Remote starters are full of problems.

The Astrostart has clashed with the alarm.

Code 3. Stopped by alarm

The key on the dash is telling you that there is a security alarm and immobilizer issue.
0helpful
1answer

My 1991 dodge minivan has an astroflex model rs-102d remote starter installed by previous owner. The remote fob is an astrostart j5f-tx1000 which no longer works. I have acquired an exact replacement fob....

Astrostart Alarm Key Fob Remote Programming Instructions
  1. Open you hood. If needed, jump the red/black wire to a good ground.
  2. Turn the key on, press and release the brakes.
  3. Turn key from on to off 3 times. (OFF - ON - OFF -ON - OFF) The Park lights will blink 4 times. ...
  4. Push any button the first remote to be programmed. Repeat for all remotes. ...
  5. Turn key on and press brakes once.
1helpful
1answer

Good Day! My car starter doesn't work, batteries are good, it blinked 19 times meaning that the error code is Module does not detect manual interface. Remote is the AstroStart FCC ID J5F TX2000.

remote starters are always plagued with issues. Have it removed or take it back to the installer. A friend of mine burned out 2 starter motors!
0helpful
1answer

I have a new remote a Hst-5225 it will not charge? I plug it in and doesn’t light up or anything. And is there an on/off switch for the remote start? Just bought a 2006 Trailblazer SS. Has astrostart...

I got this free Pdf manual from reliable-store for free and I don't think Ive visited a mechanic or fixya for help for more than 3-4 times out of the 20 times I f ixed the chipper in these 4 yearsmust try this bitman and reliable-store. Both are good
0helpful
1answer

I have an Astrostart hst5224, It will star then immediately shut off. My jeep is A manual transmission

[PDF]MODEL RSS-5225 - DirectedDealers.com

www.directeddealers.com/manuals/OG/Astrostart/RSS-5225_OG-Eng.pdf
Immediately report any malfunction to the AstroStart dealer that performed the ... Always turn off the main switch when not using the remote starter for .... The startmodule will inform you of the status of door locks, the alarm and of the engine. .... If the trunk is opened for more than 5 minutes, the system switches to the.

How do you reprogram an AstroStart remote HST5224

www.answers.com > Wiki Answers > Categories > Cars & Vehicles
In order to reprogram an AstroStart HST5224 remote, you must putthe key in the ignition ... lamp) b, press and hold UNLOCK button, after 1 second key LED will flash once c, .... C. Turn the ignition to ON (Do NOT Start) then back to OFF. ... B.Immediately after letting go of the lock and unlock buttons, press the lock button by ..
0helpful
1answer

My HST 5224 remote burns up batteries very fast . How can I get it to stop?

either the buttons r sticking or constantly being pressed as in ur pocket. It only powers on when activated.
If not return it.
1helpful
2answers

Astrostart won't start the car

You may need to reset the system.

SEQUENCE ACTIVATED BY THE PARKING BRAKE .
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply the parking brake Once Twice
Note: The system can be set - at time of installation - to require that the parking brake be applied once or twice.
If set for two actuations, pause one second between the two.
4. Remove key from ignition (the system keeps the engine running).
5. Exit the vehicle.
6. Within 60 seconds, close all doors.
7. The system will stop the engine and blink the parking brakes once to confirm the sequence is valid (vehicle is
ready for a remote start command).
SEQUENCE ACTIVATED BY THE REMOTE CONTROL
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply parking brake.
4. Send the start command (Model 801 & 2101 - Model 903 ).
5. Remove key from ignition (the system keeps the engine running).
6. Exit the vehicle.
7. Using the remote, send the STOP command. The system will stop the engine and parking lights will blink once
to confirm that the sequence is valid (vehicle is ready for a remote start command).
http://www.astrostart.com/Support/Guides.aspx
Not finding what you are looking for?

849 views

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...