Question about 1990 Honda CRX

Open Question

Replacing clutch cable in 1991 honda crx

Rreplacing clutch cable in 1991 honda crx

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 72 Answers

SOURCE: crx cable clutch problem

The clutch assy. is worn out. When a clutch is new the springs on the pressure plate sit flat. When you push on the clutch the springs don't have to move far to disengage, making it easy to press on the clutch pedal. As the clutch wears the fingers of the clutch spring move out, clutch pedal effort and travel increases to the point that the clutch will not disengage anymore. Along the life of the clutch the cable can be adjusted to minimize this. You have reached the end of the adjustment, sorry for the bad news but the clutch needs to be replaced.

Posted on Apr 19, 2009

Ad
  • 148 Answers

SOURCE: 1991 honda crx starter want engage.

check the wire going to the clutch or tranny switch for power from the ignition switch if there is no power there the ignition switch needs replace

Posted on Jul 20, 2009

YellowNo5
  • 268 Answers

SOURCE: how do i change a clutch in a 1990 honda civic crx

There's no trick to it, this is not in perfect order but it will help... You have to jump in, don't be afraid. Everything is just nuts and bolts. Drain the gear oil out of the trans, disconnect everything in the way, remove starter, all trans bolts, remove outer tie-rod bolt and pop the joint, remove lower control arm bolt on each side and pop the joint, (DON'T HAMMER THE THREADS ON THE BALL JOINTS, SMACK THE THICK METAL ON THE SIDES OF THE KNUCKLE / SPINDLE UNDER THE RUBBER BALL JOINT SEAL AND THE JOINT WILL POP OUT) push suspension up and pop out the axles. Remove motor mounts that connect to your trans. Pull the trans out or pry it carefully, MAKE SURE EVERY BOLT IS OUT. You'll also need to prop the engine up with a jack and something soft like wood or layers of cardboard. The trans will slide out but it's a few inches then it will want to drop so have something under it like a skateboard or a creeper with layers of cardboard to protect both. Don't let it slam down and hit the spline coming out of the engine. Your new clutch kit will have instructions and an alignment tool in the package to complete the clutch install. Then slap it back together. Could take 5 hours your first time, about 2.5 next time.

Posted on Sep 29, 2009

Testimonial: "thanks cuz i had no idea how to do that this will help me out alot"

YellowNo5
  • 268 Answers

SOURCE: How do you install adjustable lowering coilover

NOT NECESSARILY IN ORDER: Remove the 2 nuts from the top of your shock tower under the hood - remove the pivot bolt at the bottom of your shock fork - remove the upper control arm ball joint nut - remove the lower control arm ball joint nut - bang on the thick metal near the ball joints with a hammer (not hitting the rubber or the ball joint's bolts - remove the tie rod ball joint nut and do the same with the hammer - pull the shock and spring assembly out - You might need a spring compressor to take out the stock spring safely - remove the nut on top of the shock - It's recommended that you replace your shocks now - install the new springs according to the directions with the package - get a camber correction kit for your car - put it back together and immediately go pay for an alignment. Good luck.

Posted on Oct 03, 2009

philschneide
  • 448 Answers

SOURCE: ac compressor clutch relay 1991 honda accord

Difficult to describe, but I will give it a try.
Inside the driver's side fender, close to the front of the car, there is a bracket that is held in place by one bolt, but which has a short horizontal bar as part of it which has two large clips encircling two cylinderical devices which have wires clipped into them at the bottoms. The one closest to the front (radiator) is the compressor clutch relay. The other one is the condenser fan relay.
Hope this helps you find it.

Posted on Oct 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the firing order for a 1991 crx si


the firing order for your 91 crx should be 1, 3, 4 and 2. You need to identify where the rotor points to when cylinder 1 is at top dead center.
Cylinder number 1 is the one closest to the accessory belts (alternator, power steering , etc, hope this helps.

Aug 10, 2014 | 1991 Honda CRX

1 Answer

What is the firing order for a 1991 crx si


All Honda 4 cylinder engines that I have worked on have a firing order of 1342. That is the firing order on your CRX. #1 is the cylinder closest to the timing belt.

Aug 10, 2014 | 1991 Honda CRX

1 Answer

Manual transmission 91 honda crx will not go into gear shortly after start up or when vehicle is off.


Brian
I see this is an older post. I have a 90 Crx and was wondering if you still have the car and how you solved the problem?

Apr 01, 2013 | 1991 Honda CRX

1 Answer

What tools are needed for clutch replacement on 1991 honda crx


only an alinement tool from hire shop dont forget a new bearing should also be fitted

Nov 11, 2009 | 1991 Honda CRX

1 Answer

1991 honda crx starter want engage. Starter turns over, but wont start by turning the key.


check the wire going to the clutch or tranny switch for power from the ignition switch if there is no power there the ignition switch needs replace

Jul 19, 2009 | 1991 Honda CRX

1 Answer

1991 honda crx si m/t almost impossible to shift after it warms u


Have you adjusted the clutch cable enough to allow it to disengage the clutch ? try that first. Is this the original clutch?

Jun 11, 2009 | 1990 Honda CRX

1 Answer

Crx cable clutch problem


The clutch assy. is worn out. When a clutch is new the springs on the pressure plate sit flat. When you push on the clutch the springs don't have to move far to disengage, making it easy to press on the clutch pedal. As the clutch wears the fingers of the clutch spring move out, clutch pedal effort and travel increases to the point that the clutch will not disengage anymore. Along the life of the clutch the cable can be adjusted to minimize this. You have reached the end of the adjustment, sorry for the bad news but the clutch needs to be replaced.

Apr 19, 2009 | Honda CRX Cars & Trucks

1 Answer

1991 CRX rear disc conversion


you would have to check the axle is the same

Feb 18, 2009 | 1991 Honda CRX

2 Answers

Switching transmissions


First make sure you know what your trany came out of . honda did not go hydro until 92 all i do are honda swaps . get on e-bay they offer a kit or you will need clutch master and slave cylinder and the lines out of a doner car .Good luck and hope this helps you!

Jan 26, 2009 | 1991 Honda Civic

1 Answer

Cable transmission in my Honda


u need to get a spedo gear out of any cable b series trans and use it then it is a little c clip kinda looks like what holds a door handle on u can find them at any autopart store

Sep 11, 2008 | 1991 Honda CRX

Not finding what you are looking for?
1990 Honda CRX Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...