Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on May 23, 2012

Key fob wont re set on my ssan yan rexton

Jusy changed battery on key fob alarm keeps going off and car wont un lock

1 Answer

yasir mahmood

Level 1:

An expert who has achieved level 1.

  • Contributor 1 Answer
  • Posted on Mar 05, 2015
yasir mahmood
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Mar 05, 2015
Answers
1
Questions
0
Helped
6459
Points
0

I recently changed the battery on my key fob for my ssanyong rexton. I then did the following for the key fob to make it work. 1. Enter vehicle and close all doors.

2. Put seatbelt on (or clip it into the buckle) to shut the warning buzzer off.

3. Put key in ignition, turn to run position but don't start it.

4. Press and hold both buttons on key fob until red light on fob stays on. Then let go of both buttons. Then pressed the alarm button then the panic button, somthing like that. To be fair the button sequence after the red light came on is a bit vague. The alarm was blaring so i was happy when it just stopped.

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Dec 20, 2008

SOURCE: i have a grand voyager

dont go through all the hassles of removing the door trim just take the terminal off the battery for about a minute then reconect again worked on mine good luck

Ad
emissionwiz

Marvin

  • 85242 Answers
  • Posted on Oct 16, 2008

SOURCE: key fob will not undo

If you don't have one that works for the vehicle now, you'll have to take it to your local dealer to have it programmed to the vehicle. Some will charge for this, some will do it at no charge.

If you do have a remote that is programmed and working for the vehicle, then the following steps will allow you to program another remote:

1. Enter vehicle and close all doors.

2. Put seatbelt on (or clip it into the buckle) to shut the warning buzzer off.

3. Put key in ignition, turn to run position but don't start it.

4. Press and hold the unlock button on the working key fob and hold for 4 seconds, then also press the panic button.

5. Release both buttons and you should hear a single chime to indicate it is in program mode. You have 30 seconds after the chime to program any additional remotes you want to program.

6. Press and release both the unlock and lock buttons simultaneously on the remote you are programming. You should hear another single chime.

7. Within 4 seconds after hearing the chime, press either lock or unlock button on remote that you are programming.

Anonymous

  • 1 Answer
  • Posted on Jan 09, 2009

SOURCE: renault megane key fob wont work

I had the same problem with mine

your key fob is now out of sync with the ECU to sync them just follow this link (renault will charge up to £180 for new key and to sync it)

http://renaulthelp.110mb.com/ImmBypass.html

Anonymous

  • 1 Answer
  • Posted on Jun 04, 2009

SOURCE: car alarm preventing car from starting

I am having trouble also but I need to know how to disconnect the alarm. I would appreciate it if you could help me out seeing that you have disconnected yours. Thank you

raygin

Raygin

  • 322 Answers
  • Posted on Jul 08, 2009

SOURCE: Jag S-Type -intermitent fault where the remote fob does not work

This does not sound like a fob fault - but a locking control module fault , either in the hardware or software of the unit. Get it checked at a Jaguar dealers. When unlocking using the key - as soon as the door is opened you should hear a chime sounding inside the car - this is a timer counting down to sounding the alarm. If you put your key in the ignition as soon as you open the door the alarm should not go off and the chime should stop. If it does not this again points to a fault in the locking controller.
hope this helps - good luck.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2002 ranger super cab. Why does alarm keep going off?

Hello. It seems your truck's key fob/remote either has a low battery and/or is 'wearing out'. The computer/alarm becomes 'confused' and can't decide if it should 'arm' or 'disarm'. This also causes slow to no operation of your vehicle's door locks. Good luck and keep me informed; if you want to.
0helpful
1answer

I have a rover 45 on 05. 1.4Gli. Every time I unlock the car the alarm sounds Can any one help thanks

If you are using the key without un setting the alarm using the key fob this will happen. I'm presuming you have the key fob? If so replace the battery in it and resync by pressing lock 4 times in succession.
0helpful
2answers

Key fob won't work even after changing battery, can only open and lock car using key, alarm won't shut off and keeps ringing

retry replacing battery new doesnt mean cant be defective if it is good than fob needs a relearn different cars have different relearn that you can perform but if the fob has other features such as start that will have to be done at dealer ----
Free Keyless Remote Fob Entry programming instructions procedures for all... look up your vehicle and will have instructions one how to program fob --will also tell if need to be done at dealer
0helpful
1answer

CL220, fob wont open doors I can't get in the car, does this mean the battery is flat?

battery may be flat in the fob or the vehicle has forgotten the code for the fob. and will need resetting. change the battery use the key to open the door put key in the ignition. ( fob Ir old type leave fob off the key) turn to number 2 and press fob till doors lock and unlock. then its reset. dont be worried if the alarm goes off while doing this it will go off when the code is restored. if you have 2 fobs you will need to rest that one to.
0helpful
2answers

I just had to have battery replaced in 08 cobalt, now keyless entry will not work, had batteries replaced in both fobs, neither is working. Cant arm the alarm at all, have to manual unlock doors, and...

key in ignition 2 number 2 then press the fob. till doors lock. 2 to 3 times then unlock with fob. turn back key lock car. then un lock. then do the same with the other fob.
0helpful
1answer

Key fob flashes but wont unlock car vectra sri130 2000

yes then when you get in turn key to number to and press the fob the locks should lock the door and the fob is rest.
2helpful
2answers

2003 Audi A4 Cabriolet alarm problem. The fobs (both) keep losing sync with the car. The fobs have new batteries. The hazard warning lamp switch on the dash is illuminated constantly, and I believe the...

unlock the car with the key and hold the key over for 30 secs,(the windows will go down) then lock the car/hold key over for 30 secs,(the windows will go up). wait 30 secs then press/hold down the unlock button on the key fob,this will resyncronise the alarm/key fobs.
Not finding what you are looking for?

6,469 views

Ask a Question

Usually answered in minutes!

Top SsangYong Experts

jws1013

Level 3 Expert

1713 Answers

Ngoro

Level 3 Expert

3521 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a SsangYong Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...