Removal of door pad on honda jazz 2006 year model

Honda Jazz 2008 - Car Review ' Honest John

www.honestjohn.co.uk > Car by Car > Honda
Rating: 5 - ‎Review by Honest John - ‎Oct 15, 2015 Oct 15, 2015 - Door lock actuators failed on a 2010 Honda Jazz. Read more ... The2008 Jazz takes everything people loved about the old Jazz. Then takes it ...

Honda Jazz Problems, Reliability, Recalls, Faults and ...

www.autoexpress.co.uk/honda/jazz/reliability
Auto ExpressI have owned 3 honda jazz from 2002 only one fault on a 2005 model an emission recirculating solenoid failed known ..... 2008-reg Petrol, Owner for 3 to 5 years.

1st you need to open door, remove plastic trim on inside of door by the handle, there is a hole where a 25 torx screw is holding handle end cap, pull door handle in open position, slacken screw until end cap is loose, remove end cap & slide door handle to rear of door out comes the handle, check with torch for any broken parts

This is a manufactures bulletin


SUBJECT:
Inoperative Right Front Door Switches OVERVIEW:
This bulletin involves replacing the right door interior handle. The loss of ALL functions may occur when attempting to control them from any of the switches located on the right door due to electrostatic discharge through the right door interior handle. The right door interior handle must be replaced to protect the switch module from static electricity. The new handle is more resistant to electrostatic discharge. MODELS:
2004 - 2008 (CS) Pacifica SYMPTOM/CONDITION:
The vehicle operator may experience a permanent loss in ability to actuate ALL of the following functions from the right door switches: ^ Power door locks. ^ Right power mirror. ^ Right power seat adjustments. ^ Right power window control. ^ Right heated mirrors. ^ Memory functions associated with the listed systems on right side (if applicable). ^ Loss of communication with the right door switch module to Scan Tool: DIAGNOSIS:
Perform a "Hard Reset of the right door switch module. This may be accomplished by removing all power (including memory keep alive power) from the right door switch module by unplugging the module power connector. Alternatively, vehicle power may be interrupted by removing the negative battery terminal when the ignition switch is in the OFF position. If after performing the hard reset functions of the right door switches return perform the Repair Procedure.


PARTS REQUIRED:
REPAIR PROCEDURE:
1. Disconnect the negative battery cable. 2. Remove the right door trim panel
3. Remove the door tweeter speaker. Refer to the service information in TechCONNECT. Refer to 8 - Electrical > Audio > Speaker > Removal (Fig 1). 4. Remove the power seat switch. Refer to the service information in TechCONNECT. Refer to 8 - Electrical > Power Seats > right Seat Switch > Removal. 5. Replace the right door interior handle, p/n 05170261AA, as described on Mopar Instruction Sheet K6855628 included in the handle kit. 6. Install the power seat switch. 7. Install the door tweeter speaker. 8. Install the right door trim panel. 9. Connect the negative battery cable.

If you mean the exterior door handle you must remove the interior door panel.Just be sure you have the window closed before you start disconnecting things. Otherwise yo can't get to the back of the door handle. I have the same CR-V, year wise. As I recall, on the interior door panel there are two plastic plugs. It will be a TORX bit you would need to remove the bolts behind them. The rest of the panel is held on by clips. Use something like a slim putty knife to pop them. I will confirm this for you Wednesday. I will take my door panel off and send you the exact details.

On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you need to pull back the weather seal and then you can access the bolts securing the outer handle

This video will show you how to remove the door panel on a 01-05 Honda Civic. hope this helps you out.

remove screws (several... front, bottom.. door handle pocket (covered by round plastic button), door handle (behind. remove tweeter speaker assy (upper front corner). Interior panel pops out to gain access to whatever is behind it. That's it. Anything else?

yes there are screws in several places along the edges of the door panel and in or below the center handle and push pops you have to pull the panel from the edges after removing all screws only then can the truth be revealed

Hi there.

The procedure is roughly the same for all mk3 x types.
You need to remove all the screws on the armrest and on the ashtray, then undo all the plastic clips using screwdrivers on the panel.

You find detailed instructions on links below, I quote:

" remove two screws at the bottom of the armrest.
pull out ash tray.
remove screw in the middle of the ash tray holder.
pull up on armrest, it should pop up, then pull it out
start at bottom right of door and start popping out the plastic clips (all the way around the door)
(remove speaker wires)
push up door panel - done"



WikiAnswers - How do you remove a rear door panel in a Jaguar XJ6


Also from manual:

Disconnect vehicle battery ground lead.
Remove the door trim pad veneer panel.
Remove the upper trim pad.
Remove the door armrest.
From inside the door pocket, release the puddle lamp (1 Fig.1) securing quarter turn fastener.
Undo and remove fixing (3 Fig.1), (front door only)
Carefully release lower trim pad fir tree fasteners.
To avoid damage and distortion of the door metal, lift the lower trim pad complete with clip and clip retainer.
Carefully pull the trim pad away from the door panel.
Disconnect the multi-plugs (1 Fig.2) and remove the lamp.
Carefully displace the trim pad (2 Fig.1) from the door retaining clips.
Disconnect the multi-plugs (2 Fig.2) and (3 Fig.2).
Remove the door pocket.
Displace and remove the retaining clips and remove the trim..
Refit in the reverse order of the removal procedure. Check the trim pad retainers for damage before refitting.

Before refitting the lower trim pad, remove the clip retainer from the pad and and reposition retainer to the door.

ndo door handle escutcheon screw and remove escutcheon
Remove the door trim pad veneer panel.
Undo and remove the upper trim pad securing screws.
Remove the chrome strip.
Undo and remove the top channel securing nuts.
Displace and remove the top channel assembly.
Place the trim pad aside (Fig. 1).
Refit in the reverse order of the removal procedure.







Thanks Jaguar XJ6 Interior Lights

I will be grateful if you can rate the solution given.

Many thanks.

G.

I'm going to assume the 2008 is similar to my 2006. The mirror is attached to the door with (3) 10mm nuts behind the triangle shaped interior trim piece that pops off easily with a screwdriver. If you have electric mirrors, the door panel has to come off to unplug the wiring harness from the mirror. There are three T30 torx screws and a 7mm bolt that need to be removed first...two torx bolts are under the rubber pad in the door grab well and the other is under the plastic trim piece behind the interior door handle. The 7 mm screw is behind the door reflector. Once the torx bolts and 7mm bolt is removed, pry the door panel at the bottom (there is a slot for this) and release the plastic connectors around the panel's edge...some effort is required to release them.