Question about 1998 Lexus Gs 300
I have 98 lexus gs300 the engin and vsc lights are on, codes P1120, P1121. where to find and how to change accelerator positopn sensor?
Thank you in advanse!!!!
I wanted to start a thread specifically about failures within the throttle body concerning the GS300 (1998 in my case)
My symptons were:
VSC, VSC OFF, and ENGINE Lights would come on, followed by my car going into Limp Mode, where only that last 25% (if that) of the throttle would respond (basically have to floor the pedal to even move at all).
During the mornings, or when the engine was COLD, the throttle operated normal...then once the car warmed up, usually at about 10 mins, the problem would start...it happened intermitantly at first...1 or 2 days over the course of a week, then it became more consitent, until last week it became a daily problem.
The first part I tried was the Throttle Position sensor, which is on the front side of the throttle body, and the easiest thing to replace...this didnt help at all. $300 part from Lexus, $80 part from RockAuto.com (exacly same part toyota OEM)
THE PART THAT FIXED THE PROBLEM:
"Idle Valve Motor", which is the larger electrical object next to the TPS on my 98 GS300. Problem is solved.
The Codes I got were P1120 and P1121 - Accelerator Sensor problem. However it wasnt really the Accelerator Sensor, it was indeed to actual electrical Motor that controls the opening of the Butterfly valve inside the Throttle body.
I found the problem by good old trouble shooting, and using an ohm meter to see if the throttle electric motor was getting elev, I found that the elec motor just to the left of the TPS was basically freaking out and shutting down. The Accelerator Pedal Sensor is on the Back-side of the throttle body where the throttle cable connects to, and has a spring on it. It was fine.
GS300's are indeed "drive by wire" concerning the throttle...the cable triggers the Accel Pedal Sensor, which sends a signal to the ECU, the ECU then sends power to the Idel Valve Elec Motor (next to the TPS), which opens and closes the mechanical butterfly valve, then the TPS sensor detects how far the elec motor is actually opening the butterfly valve...its a closed-loop feed-back system, meaning any failure in any sensor will cause the entire systm to fail.
The throttle cable apparently is ONLY there to allow the fail-safe of having that last 10-25% throttle when the electronic system fails...there is a gearbox inside the throtle body which allows the tail end of the throttle to manually engage the butterfly valve...the rest of the time, the butterfly valve is 100% opened and closed via the idle control motor.
Posted on Jul 08, 2009
Same symptoms....at first I was told several times that it was the catalitic convertor; but was then told accelerator positioning sensor. We were going to repair it at first ourselves but the were told it would not be timed accurately so in Ga I paid $415 to have it repaired; approx $300 just for sensor and I may have burned up the membrane.
Posted on Apr 23, 2009
I just bought a used throttle body with all the sensors on ebay, took out my old throttle body w/sensors, cleaned up the used one a bit, then put it in and the car runs perfect now, no CELs!
Posted on Aug 29, 2013
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Jan 05, 2018 | Lexus Cars & Trucks
Oct 30, 2017 | Lexus Cars & Trucks
Jan 08, 2016 | 2006 Land Rover Range Rover Sport
Jan 08, 2016 | Land Rover Range Rover Cars & Trucks
May 17, 2014 | 2005 Dodge Dakota Quad
Jan 24, 2014 | 1998 Lexus Gs 300
Mar 28, 2011 | Ford F-250 Cars & Trucks
Oct 09, 2010 | 1996 Mercury Grand Marquis
14,283 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: