2002 Renault Clio Logo
sarah Posted on May 13, 2012

Central locking wiring clio

I think it's a wiring problem with central locking. Lights flash when key fob pressed but no locking mechanism. No warning light on dash, internal light indicates when car should be locked but is not. Am I right in thinking wiring?

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

  • Contributor 2 Answers
  • Posted on Oct 18, 2012
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Joined: Oct 18, 2012
Answers
2
Questions
0
Helped
2209
Points
1

I had a problem where my key fob did not lock or unlock the car, Renault Clio Dynamique, but the central locking button in the car did still work and engine turned over fine. Changed the key fob battery still nothing. Read online about disconnecting and reconnecting the car battery, (negative only) and hey presto it worked! All working fine now!

5 Related Answers

Anonymous

  • 2 Answers
  • Posted on Sep 15, 2009

SOURCE: renault key fob doesnt work

Hi.
I have a clio II, 2001, i have the same problem and i fixed it.
Don't know if will work for you but here it goes:

1 - no key in ingnition
2 - press the unlock button in console off the car for about 10 seconds(dont let go)
3 - it should work the central doors one time and then 2 times( hear)
4 - press the remote a few times until it starts working

It worked for me hope the same for you.
Please tell me if it worked and pass the message.

Good luck

Ad

Anonymous

  • 1 Answer
  • Posted on Aug 14, 2008

SOURCE: clio

Hi, have a Renault Megane car, trip computer says replace car batteries, did this but message never went away it stayed on the trip computer. Had car serviced and asked them to check my key card, staff said my card was faulty even though it works perfectly well apart from message on trip computer asking me to change battery? Also staff said my spear card would go the same war as I have never used it, I was keeping it safe for emergency use, staff said eventually both cards will de-program. Is this information correct?
Many thanks.
Noel Ivers

rgbypoet

  • 166 Answers
  • Posted on Aug 25, 2009

SOURCE: key fob lights up but doesn't work even with a new battery

I'm more familiar with Range Rovers and Saab's when it comes to key fobs but if you changed the battery you have to re-program the key fob. If you do not have an owner's manual that can take you through the steps you might want to try: push and hold the lock button on the key fob, put it in the driver's side door and turn to lock. With the button still depressed turn back to open, remove the key and release the button. If this doesn't work check any and all fuses associated with your system and last but not least you could take it to a dealer. Good luck!

Testimonial: "thanks ill try what you've suggested"

Matthew Hutson

  • 97 Answers
  • Posted on Mar 18, 2010

SOURCE: central locking

I am not very familiar with this auto maker, however it seems as if the door warning sensor is fused in the open position. I would recommend changing the sensor. I'll do some more research on this auto maker and provide more specific details on how to complete the change. Thank You

Testimonial: "that would be great"

Anonymous

  • 2418 Answers
  • Posted on Jun 06, 2010

SOURCE: Renault clio central locking fault

I believe you have to press the button very quickly 2 times. One time is just for the drivers door then two times very quick to unlock all..

Testimonial: "Brilliant!! Just tried that and it works. Thanks very much."

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My hyundai i10 wont lock or unlock when using the press button on the key

Hyundai Grand i 10 Central lock module resetting process (2014 Model) Step 1 Enter car and close all doors. Step 2 Kept Fob key in hand Step 3 Repeat the below process 5 times 1 Turn on the Acc mode, Press the Fob key lock button 5 times and turn off the Ignition switch 2 Turn on the Acc mode, Press the Fob key lock button 5 times and turn off the Ignition switch 3 Turn on the Acc mode, Press the Fob key lock button 5 times and turn off the Ignition switch 4 Turn on the Acc mode, Press the Fob key lock button 5 times and turn off the Ignition switch 5 Turn on the Acc mode, Press the Fob key lock button 5 times and turn off the Ignition switch End After head a small beep from central lock module stop the process ( Beep sound is the Success Signal)
0helpful
1answer

Central locking wont work cant open it except drivers door with key only,but alarm still work with key fob.

put key in ignition turn key to number 2 lights on dash battery etc. then press the fob. till the doors lock then it is rest.
0helpful
1answer

How do i reset central locking on a micra 04 reg

Try the following:

"KEY FOB PROGRAMMING
NISSAN
SYSTEM DESCRIPTION
The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and hazard reminder. When the doors are locked and
unlocked the unit flashes the hazard lights once for lock and twice for unlock.
A maximum of four remote controls are allowed to be programmed.
ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II
Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.
Procedure
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key?s.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key?s for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds."
2helpful
1answer

Renault clio central locking fault

I believe you have to press the button very quickly 2 times. One time is just for the drivers door then two times very quick to unlock all..
4helpful
2answers

Hi, I have an imported 2004 Subaru Impreza WRX. How do I reprogram the key fob after changing the battery.

first unlock car manually with key remove driver side kick panel/lower A pillar trim connect locking registration wires together(two white connectors,black wire and black and blue wire)press and hold central locking switch on drivers door in the unlock position .interior lamp will flash and an acoustic sound will be heard. now get your key and press unlock and then lock the door should lock then unlock, job done ,i persume it was to program the fob to work the central locking u wanted
0helpful
2answers

Central locking doesnt work on mk2 clio t reg

try putting the key in the ignition and turning it to on then holding the unlock button for 30 seconds and then remove the key and try the remote if still no good go to your dealer and get them to reinishalise the system
4helpful
1answer

Renault key fob doesnt work

Hi.
I have a clio II, 2001, i have the same problem and i fixed it.
Don't know if will work for you but here it goes:

1 - no key in ingnition
2 - press the unlock button in console off the car for about 10 seconds(dont let go)
3 - it should work the central doors one time and then 2 times( hear)
4 - press the remote a few times until it starts working

It worked for me hope the same for you.
Please tell me if it worked and pass the message.

Good luck
3helpful
2answers

Key fob lights up but doesn't work even with a new battery

I'm more familiar with Range Rovers and Saab's when it comes to key fobs but if you changed the battery you have to re-program the key fob. If you do not have an owner's manual that can take you through the steps you might want to try: push and hold the lock button on the key fob, put it in the driver's side door and turn to lock. With the button still depressed turn back to open, remove the key and release the button. If this doesn't work check any and all fuses associated with your system and last but not least you could take it to a dealer. Good luck!
1helpful
3answers

Clio

the key has lost its code. open the doors manually and use the central locking button inside the car. hold it down and keep pressing your key fob. this should re code the key
Not finding what you are looking for?

2,104 views

Ask a Question

Usually answered in minutes!

Top Renault Experts

xxxxxx xxx

Level 3 Expert

5117 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...