2007 Chevrolet Tahoe Logo

Related Topics:

A
Anonymous Posted on Nov 28, 2017

How to fix auto start for 2007 tahoe

I'm having a problem with my remote keyless entry control device, before I can make my tahoe start remotely, but now its not working. Is there any programming needed? I already change the remote battery and still not starting but the other basic functions are doing well. Hope you can give me any good advice. Thank you!

5 Related Answers

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Sep 30, 2008

SOURCE: programing keyless entry

If you have an owners manual the programming instructions are in there. If no manual here they are:

1. Turn the ignition off.
2. Ground the receiver program terminal. Jump the two terminals located in the programing ground connector. (What this means in simple terms is locate the wires that run on the right side of the trunk. There is two black wires that has a plug on the end with two prongs. It is in between the antenna and tail lights.)
3. Within 2 seconds of connecting the prongs the door locks will lock. The unlock and the rear compartment lid release will produce a cycle, causing the horn to chirp. This indicates that the module is ready for reprogramming.
4. Press and hold the lock and unlock buttons at the same time until the doors lock and unlock. The rear compartment lid will release and the horn sounds to indicate that the transmitter has successfully been reprogrammed. (Hold buttons down for approximately 12 seconds)
5. Repeat the previous step for the remaining transmitters.
6. Remove the jumper at the program connector.
7. Verify the proper operation of each transmitter

Ad

Anonymous

  • 2 Answers
  • Posted on Oct 29, 2008

SOURCE: Change battery/Reprogram remote

take the postive battery cable off then put it back on then turn your car over three times not start it but just turn it on off on off on off that should reset it. thats what they did to mine at the dealers and it cost me 120.00 bucks

Anonymous

  • 33 Answers
  • Posted on Mar 28, 2009

SOURCE: remote keyless entry not working

KEY FOBS FOR THIS MODEL MUST BE PROGRAMED USING A TECH 2 SCAN TOOL SO IT MUST BE DONE AT THE DEALERSHIP FOR ABOUT HALF HOUR LABOR HOPE THIS HELPS

Anonymous

  • 206 Answers
  • Posted on Apr 08, 2009

SOURCE: program a keyless enrty remote start 2004 chevy malibu

Dealer only If you find a different means let me know

Anonymous

  • 1 Answer
  • Posted on Sep 08, 2009

SOURCE: Key remote stopped working

I HAD THE SAME PROBLEM, CHANGED OUT BATTERIES IN MY REMOTES AND HAD THEM TESTED AND THEY WORKED FINE. THEY DEALERSHIP STATED IT WAS NOT UNDER WARANTY AND IT WOULD COST $600 TO FIX IT. YOU CAN ONLY REPLACE IT THRU A CHEVY DEALERSHIP. KIND OF A SCAM!

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

What are the locations of the Remote Control Door Lock Receivers RCDLR in a 2015 Malibu?

According to GM there are 3 components in the RCDLR or RKE remote keyless entry system. My key fobs with new batteries only work standing right next to the car. The range of the key fob dropped at that the same time my TPMS tire pressure monitoring system repair warning came on my dashboard. The problem is that there are 4 different components on the 2015 Malibu. I will provide the GM part numbers for these, if you please tell me where they are and also how to replace them: #13583559 Remote Control Door Lock Receiver #13502554 Antenna #13502551 Ignition Lock Key Transmitter Antenna #13502549 Low Frequency Console Antenna
0helpful
2answers

How Do I Know If My Car Equipped With A Keyless Entry Remote System? I have a 1999 Ford Windstar. I bought several remotes but can't get my locks to engage. Any help would be appreciated.

Hello Cathy

It does indeed have keyless entry. It needs reprogramming when you get a new remote. Also if you disconnect the battery. Usually a local car alarm fitting shop, or an auto-electrician will do it. Plus of course a Ford dealership.

https://www.google.com/search?q=Keyless+Entry+Remote+System+1999+Ford+Windstar

..
1helpful
1answer

Which fuse powers the power door locks on a 2012 equinox? None of the doors lock or unlock with the fob, battery ok

The Lock's lock from the door switches ? If they do it's not a fuse problem . Which of these does your vehicle have ?
Keyless Entry System Description and Operation (with Accessory 2 Way Remote)
Keyless Entry System Description and Operation (without Accessory 2 Way remote)

The keyless entry system is a vehicle entry device. The keyless entry system is used in conjunction with the body control module (BCM) to remotely activate certain vehicle features. Keyless entry will lock/unlock the doors/liftgate when a corresponding button on the keyless entry transmitter is pressed. This is accomplished by the transmitter sending a radio frequency to the remote control door lock receiver (RCDLR). The RCDLR interprets the signal and activates the requested function via a serial data message to the BCM. A low transmitter or vehicle battery or radio frequency (RF) interference from aftermarket devices, such as 2-way radios, power inverters, computers, etc., may cause a system malfunction. High RF traffic areas may also cause interference that could lead to a malfunction. Keyless entry allows you to operate the following components:
• Door locks
• Liftgate lock
• Vehicle locator/Panic alarm
• Illuminated entry lamps
• Remote vehicle start
The keyless entry system has the following components:
• Keyless entry transmitters
• Keyless entry antenna
• 2 Way Advanced Remote Start RCDLR
• BCM

Your best bet , take it to a GM dealer .
0helpful
2answers

Changed battery in keyless remote and now doesn't start car or open doors

  • HOW TO - Change the battery and quick fix your car remote ...

    ? 9:32
    https://www.youtube.com/watch?v=KzCXGXCe0oc
    Sep 1, 2011 - Uploaded by tyreeztt
    Also if your remote isn't working with a new battery please check out this ... TO - Change the battery and quick fix your car remote / keyless entry ...

    Remote Key does not lock / unlock doors after battery change ...

    www.6speedonline.com/.../208274-remote-key-does-not-lock-unlock-do...
    Apr 17, 2010 - After I changed the battery, it would no longer lock / unlock the doors. ... I can start the call and all .. its just the door and trunk lock / unlock function that does not seem to work . ... now your fob is learned... the keyless entry goes into a "sleep" mode to preserve the batt.. if u do not use the ... Still don't work .

    how do i reprogram my lock remote to my car? i changed my ...

    www.cargurus.com > Questions > Hyundai > Tiburon

    CarGurusAug 17, 2009 - i change my battery an now my lock an un lock buttons dont work on my remote how o i reprogram it? ... I have a Hyundai 2003 Tiburon, and the followingworked for me, get ... However for a replacement keyless remote fob, you will have to go to ... And no, they don't do it for free (ranges from $30-$50 in my ...

    Top 5 Tips in Fixing a Keyless Remote ' eBay

    www.ebay.com > ... > Safety & Security > Keyless Entry Remote / Fob
    Key fobs that don't permit entry can be a major hassle for drivers, but fortunately, there... Drivers with a bit of basic electronics experience are often able to replace their ...After confirming that a remote is faulty, try replacing its battery. ... like "Jeep Wranglerkeyless remote," to find listings that will work with specific vehicles.

0helpful
1answer

My 2007 keyless entry remotes have stopped working how can I fix them?

Keyless entry remotes allow you to put down and roll up the windows in your car. You would have to have the power windows feature installed on your keyless remote. --------------------------------------------------------------------------------------
VVDI VAG Vehicle Diagnostic
0helpful
1answer

2008 HHR Remote Starter not working

Is this an issue with all 2008 HHR remotes??? Highly doubtful , probably the vehicles keyless entry system . Taking the vehicle to a qualified repair shop an having the keyless entry system checked for DTC'S - diagnostic trouble code's . Do you know what a DTC is ?
The keyless entry system is a vehicle entry device. The keyless entry system is used in conjunction with the body control module (BCM) to remotely activate certain vehicle features. Keyless entry will lock/unlock the doors, or release the rear compartment lid when a corresponding button on the keyless entry transmitter is pressed. This is accomplished by the transmitter sending a radio frequency to the remote control door lock receiver (RCDLR). The RCDLR interprets the signal and activates the requested function via a serial data message to the BCM. A low transmitter or vehicle battery or radio frequency (RF) interference from aftermarket devices, such as 2-way radios, power inverters, computers, etc., may cause a system malfunction. High RF traffic areas may also cause interference that could lead to a malfunction. Keyless entry allows you to operate the following components:
• Door locks
• Liftgate lock
• Remote rear doors (Panel only)
• Vehicle locator/panic alarm
• Illuminated entry lamps
• Remote vehicle start
The keyless entry system has the following components:
• Keyless entry transmitters
• Keyless entry antenna
• 2 Way Advanced Remote Start RCDLR
• BCM

Guessing will not fix this .
2helpful
1answer

How to program keyless entry remote for buick lacrosse?

I own a 2007 Buick Lacrosse, but I imported it to Paraguay, South America. Now I bought a new Engine Start Keyless Entry Remote from Amazon, but here we do not have any GM dealer to program the unit.
I really need help to program the keyless remote control, I will appreciate very much your help.
2helpful
1answer

I changed the car battery on my 07 chevy tahoe and both remotes are not working any more? do I have to go to the dealer in order to program them.

No. turn the key to the on position (not run). In your driver Information Center you should have an option to program your keyless entry. Access this option through your steering wheel controls. There are two buttons. One is a page button and the other is a select button. It will guide you to the reprogramming just make sure you do both remotes at the same time unless you only have one remote. When you are prompted to begin programming hold the lock and unlock buttons at the same time on the first remote and wait for it to program. Then do the second remote the same way. When you are done turn the key off then start the engine and confirm they work.
1helpful
3answers

Keyless entry

I had the same exact problem and fixed it by disconnecting the battery for 5 minutes. I was also having a problem with the A/C compressor not kicking in and after the battery disconnect it is working fine.
Not finding what you are looking for?

160 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...