Question about 1995 Toyota Corolla

3 Answers

Car cranks hard but won't start

As far as I know all the fuses are good, but for some reason it's not firing to start. It does have gas in it, almost a quarter of a tank. I think the car sat for a good while. I just bought it and the guy won't call me back. This is the second time in 15 days that it has broken down.

Posted by on

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 37 Answers

May have to bleed feul system. If it's injected its simple. Crank the car then take something to open bleeder value. If no fuel then crank the car while holding valve open. Should bleed air out and have steady squirts of fuel.

Posted on Jan 08, 2018

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 5 Answers

Sounds like no fire to the motor try changing out the plugs and wires to new ones and see what that does.

Posted on Jan 08, 2018

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Loyalty:

    Visited the website for 30 consecutive days.

  • Master
  • 318 Answers

The two big categories for cranks but failure to start are
1) no fuel
2) no spark
Things to check for no fuel: a) out of gas which you have checked so that is not the issue, b)bad fuel pump, c) clogged fuel filter
Things to check for no spark: a) see if you have any spark...lots of websites and videos about this b) bad pickup sensor in ignition system c) bad timing
Good luck on further troubleshooting..

Posted on Jan 08, 2018

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 89 Answers

SOURCE: 1999 Toyota Camry V-6.

when starting push gas, if runs
idle valve (IAC) stuck,replace or disassemble and clean the burrs
has two time this promblem

Posted on Mar 01, 2009

  • 21 Answers

SOURCE: Idle Problem After Refueling

Sounds like the valve in the gas cap has failed, try replacing the gas cap with the correct one listed for your vechicle

Posted on May 04, 2009

michigan man
  • 3533 Answers

SOURCE: Car won`t start,stalled and didn`t start back.

checkout the crank sensor and the engine timing also checkout these websites www.autozone.com and www.alldatadiy.com

Posted on Jul 30, 2009

  • 4 Answers

SOURCE: toyota wont start

EFI= to Electronic Fuel Injection. If you have sparks, check for fuel delivery. Another is the electronic module on your distributor, but you already said you have spark and hopefuly the right "timming" too. So you checked the current and is OK, what else do we have.The computer? Remeber that Camry,is the cadillac of the Toyota. Some even have Lexus parts. So expect parts to be rather expensive!.

Posted on Aug 07, 2009

  • 16 Answers

SOURCE: EFI fuse Keeps Blowing

I had the same problem at one point. My issue was a bad grounding point from the battery to the chassis. I would say check all of your grounding points.

Posted on Nov 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 Oldsmobile 88 Royale turns over, gets fire and gas but won't start


Crank position sensor...i have same car and that happened to me

Oct 14, 2012 | 1994 Oldsmobile 88

1 Answer

Hard to start husaberg 1998 fe400e fires but will hurt you some times you can crank on 2 kicks and shut off and not get it to start its firing but seems to be out of faze.Like timing is off to far adv


You may have this posted in the wrong product category. Please select another category appropriate to the problem and re-post the problem so the correct expert will see and respond to the question..
This is for car and truck problems related to factory installed systems not add on aftermarket systems.
This post can't be removed or moved, please re-post the question in the correct product category. Thanks

Oct 10, 2012 | Cars & Trucks

2 Answers

What are diods #'s 1 & 2 on a 2004 Kia Optima fuse panel, #'s16 & 17?


always check the simplest things first. is it getting spark? if so, is it getting gas? if so, is it getting enough gas? and so on...

Jan 21, 2012 | 2004 Kia Optima

1 Answer

Car died while driving, cranks, but won't fire, no communication with scan tool as far as engine or transmission. It will communicate with body.


did you say scanner not powering up or you not getting any code.because if engine not firing a faulty crankshaft position sensor or ignition module will cause no spark conditions.also check 20 amp ignition fuse to ignition coils and ignition module,check ignition battery feed 10 amp fuse to the pcm.check at the 16 dlc terminal at top ground terminal 4 that would be fourth terminal top from left to right.and check bottom far right terminal 16 see if you getting getting battery power.if fuse all good no power at terminal 16 your pcm could be getting poor ground contact or problem in the pcm thats not a home fix dealership has to run diagnostic scan test look for pcm fault or wiring fault.

Nov 29, 2011 | 1999 Cadillac Eldorado

1 Answer

Car won't start powerwindows won't work powerlocks won't work all fuses are ok I think when car was boosted they put cables on wrong terminals I tried boosting it will crank but will not start...


check your ignition fuse and relay fuse.also check your master fuses located on the fire wall they are the ones that run from your nattery to your maine master fuse.follow the battery cable the red one all the way to the fire wall and from there it gos to the starter you may have burned thoses fuses out remove the black fuse cover

Sep 09, 2011 | 2004 Chevrolet Impala

2 Answers

2000 nissan maxima won't fire when trying to start. it turns over but won't fire. it started once and ran but won't start again


sounds like it might be flooded. Try and remove the fuel pump fuse from the fuse block that is just in front of your left knee. While it is out crank the car and see if it wants to start and hold down the gas pedal all the way and then relase it and back and forth and once you get it to run have the fuse ready in your hand and in front of the spot to install it. and then keep the rpm's up with the gas pedal until the smoke clears out behind the car.

Jul 02, 2011 | 2000 Nissan Maxima

3 Answers

I have a 1998 Chevy Cavalier that I can not figure out why it won't start. The following list of parts are brand new: Battery, PCM, Park Neutral Safety Switch, Alternator, Ignition Switch, and finally...


Your car has a sealed transmission, in order to check it you have to go to the dealer or a transmission

shop, its not owner servicable. takes dextron vi, 4 speed 7.4 quarts, 3 speed 4quarts

And as far as the no start, are your plugs getting voltage, if not check your coil, if there is no spark

to your plugs the car will not fire up. good luck!

Jun 26, 2011 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
1995 Toyota Corolla Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...