I replaced the rear shoes on the van. It has ABS disc brakes. Now, The emergency brake will not hold. I crawled under the van and found the emergency brake cable & saddle bracket (for the cables going to each rear wheel). In past experiencies, the emergency brake cable has a nut on the end of the cable (coming from the pull handle) that allows for adjustment on the emergency brake. This one doesn't, just a "keeper" stop on the end of the cable from the handle. went back to the wheels and checked at the calipers for anything for emergency brake adjustment, and if there is such a thing...I couldn't find it. I then went to the handle itself and removed the cover looking for an adjustment mechanism. Nothing...Am I missing something somewhere???HELP....
Over here we call it a parking brake - hardly any of our cars are autos.
Parking brakes usually connect to the rear disc brake calipers but some manufacturers use a small drum brake in the disc centre for parking purposes due to the complexity of the caliper with integral parking brake.
When adjusting a parking brake it is important in most designs for the cable to be adjusted only to remove any free play without moving the caliper levers from the backstops and then if the parking brake lever or pedal travel is excessive it must be because of wear or other faults. Sometimes that basic requirement must be taken with a pinch or two of "experienced" salt...
Ford have a self adjusting parking brake I have experience of. A spring within the system preloads the cable eliminating all slack in the cable so the cable moves the caliper levers from the first. The main problem with the system is the preload spring is sometimes strong enough to overcome the resistance of the caliper spring and cause a binding brake. No manual adjustment was provided.
In that case I find fabricating and fitting brackets to anchor additional return springs to the calipers is a must.
SOURCE: 93 Ford thunderbird parking brake adjustment
on most of the cars us use a special spanner tool that resembles a bent screwdriver. you pull the plastic cap out from the back of the drum and then just turn the ajustment wheel till you feal it tighten up a litle. Remember to put the plastic cap back on. Also a old trick most people don't know about is put the car in reverse in a parking lot, and slam on the brakes. most cars have a auto ajustment that they never use.
SOURCE: How to fix the emergency brake cable?
I do not know what car you are working on but most have the adjustment on the front cable.
SOURCE: Emergency brake adjustment
I have a 2000 4x4 expedition and the parking brake has its own set of shoes. They are located behind the rear disc rotor. You have to remove them to get to the shoes. You will have to release the parking brake to get the rear rotors off.
Izap2
SOURCE: how do I adjust emergency brake cable on 1999 ford
FIRST adjust rear brake starwheel while spinning tire FOWARD. then alongside drivers side of car find emergency brake cable adjustment (long threaded rod with nut) . hold one end of rod with vise-grips and turn nut until emer. brake cable has less slack in it. now go inside car and apply e-brake.you dont want the pedal to stop right away but u also dont want too much"travel" in the pedal.so about halfway is IDEAL. IMPORTANT- once the brake cable is adjusted and the car wont roll foward in gear with the brake on and applying a little "gas"-make sure with brake OFF that rear wheels turn freely. hope this helps.
SOURCE: 98 Ford Escort, Emergency brake doesn't hold car.
If you have rear rotors that look like a rotor mounted on top of a drum brake, you will have an emergency brake inside the drum portion. The rear brake rotors are not flat like the front rotors for this style.
The E brakes have brake shoes and they have "Star" wheels for adjustment just like the regular drum brake. You really need to take off the rear rotors to inspect the inner drum portion. If you do adjust the E brakes without looking at the drum part, chances are the drum is pitted and rusty and you will be lucky to stop once before the E brake linings are ground off.
The other type of E brake works off the Rotor pads. You will see the brake cable attached to a lever on each wheel. There will be an Equalizing cable connecting both rear wheels with an adjustment point joining the main cable. Although the 3 clicks moves the main cable, to have both rear brakes equally tight you need the Equalizing properly adjusted.
Those are the things you need to look for.
791 views
Usually answered in minutes!
×