Question about 1994 Lexus LS 400

2 Answers

My egr wire harness plug that plugs into the egr, became brittle. And fell apart as I disconnected it. Is there a way to know which wire goes to which leg in the egr, I have a 94 Lexus ls 400. Car seems to run better without plug, just the check engine light stays on, is there any help for problem?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 109 Answers

An easier way might to go to your local parts store and buy what is called a pigtail . Then just color match it and plug it in. Plastic parts are not what they should be and Heat seems to make them very brittle . good luck.

Posted on Sep 18, 2018

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lexus Master
  • 637 Answers

Let me know if this helps.
My egr wire harness plug that plugs into the egr, - screen shot 2018-09-17 at 11.29.20 pm-4dqggl4oy441eg12cufqdvnl-4-0.png

Posted on Sep 18, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: all dash warning lights came

Hatterasnc,

You're alternator has gone bad and the vehicle was running on battery power. The "clicking" sound is your now dead battery that does not have enough power to turn over the starter. You might also want to check your power steering pump for leak. This is a know problem with early LS400s and will most likey be the cause of the alternator failure. I just dropped $1050.00 to fix the very same promblems you have.

Posted on Jul 21, 2008

  • 1 Answer

SOURCE: 1994 lexus ls 400 problem with dash board light

Try rotating the ignition switch slightly after you turn it to on and see if the lights come on...had the same problem and changed the switch fixed the problem...

Posted on Feb 14, 2009

farroutideas
  • 78 Answers

SOURCE: 96 lexus es 300 blinking check engine light

Hi there;

#4 Miss-fire. All the things you are saying make a lot of sense. When the light is blinking the cylinder is actualy misfiring, & the smell you are smelling is the fuel that is not burning in the engine burning in the exahst. This can cause a lot of damage to the exausht if it is not repaired..
There is still a couple of things that need to be checked, first he needs to check to see if it is possibly a fuel injector that is sticking. He can do this easily by moving the #4 injector to another cylinder & run the car. When it starts missfiring he will need to see if it is still #4 or if it is the cylinder that he moved the injector to. if it is the new cylinder it is obviously the injector, if it is still #4 he will need to look into the possibility of the EGR valve sticking open or some other issue to do with valve timing or low compression.
I hope this helps
Farrout!

Posted on Mar 17, 2009

mecanica03
  • 918 Answers

SOURCE: Trac Off and Engine light stay lit

well, the first to do is an oil service to your car, after disconnect the negative battery terminal few minutes to reset

Posted on Apr 15, 2009

mkv0525
  • 358 Answers

SOURCE: 92 lexus ls 400 check engine and traction control light came on at the same time, 92 lexus ls 400.

the track off light will come everytime yhe check engine light comes on. this is normal. you need to have the check engine light checked first.you can go to your local parts house they will scan it for so you at least see what area you problem is in and then you can start from there. let me know lf you find out youe engine codes.

Posted on May 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many wire harness clips connect to module besides the antenna


Engine Control Module Wiring Harness Replacement - 1.4 L ...

workshop-manuals.com/.../repair.../engine_control_module_wiring_harn...
3. Unclip the 3 wiring harness clips (1, 2) from the engine control module wiring harness brackets. ... Disconnect the wiring harness connection adapter plug (4).

Engine Control Module Wiring Harness Replacement - 1.6 L ...

workshop-manuals.com/.../repair.../engine_control_module_wiring_harn...
5. If equipped, disconnect the engine oil level sensor wiring harness plug (7). ... 10. Unclip the 2 wiring harness clips (2, 6) from the wiring harness brackets.

How to fix wires that break out of plug clips on a wire harness



Dec 01, 2015 | Cars & Trucks

1 Answer

Replaced spark plugs on a 2004 Explorer. Car became loud and tinging and eventually died? What could be wrong?


It is possible that you have two or more plug wires on the wrong spark plugs or one of the wires fell off the plug.

Feb 08, 2015 | Cars & Trucks

1 Answer

Where is the knock sensor bank 2 wiring harness located


Hi John, The knock sensors on both banks are fitted as closely to the cylinder head as possible. The knock sensors 'listen' to the ignition and adjust spark timing accordingly. They are fitted onto the hottest place on the engine and consequently the cables often get heated and hardened and easily break. The sensor is usually under the intake manifld (making it fairly hard to find, but it will be there. Regards John

Aug 19, 2014 | 2006 Buick LaCrosse

2 Answers

The check engine light came on i my car so I took it up to checkers. They scanned the car and a code came up reading cam shaft position sensor. I got it replaced but, the code is still coming up and my car...


The problem may be unrelated to one another

Are the plugs NGK factory recomended plugs gapped properly?

Or are they bosch platinum or other brand?

Did you have the original codes cleared by disconnecting your battery and reconnecting it?

It could just be that the plugs are not the right type OR you may have the wrong wires or teh harness plug is broken.

Mar 31, 2010 | 2001 Hyundai Sonata

2 Answers

93 mercury villager check engin light comes on for 2 days then off for a day then back on i dont know where to plug in my scanner


I too have a 93 Villager. Recently the check engine light came on especially on the highway cruising speed and it turned out to be caused by clugged EGR. My mechanic cleaned up the carbon build-up ( not replace EGR) from all those 170K miles and it seems to fix the problem. He charged me $150 for the labor only. Also the gas mileage seems to improved a bit as well.

Oct 27, 2009 | 1993 Mercury Villager

2 Answers

How do you access and remove the valvecover on a 1989 firebird formula 350 (Side the AC unit is on.)? I tried to change my gasket, but was unable to get enough room to take the cover off.


ON these you do need to remove the a/c compressor. You do not need to undo the hoses but unbolt the compressor and set it asside out of the way. Be vary careful in doing this so not to break the hoses or anything else. You may have to remove the a/c brackets as well. Just remember how they come apart so you can put them back. Let me know how you did. and if you need more info. Please leave feedback.

Jun 21, 2009 | 2002 Pontiac Firebird

1 Answer

Fuel tank wire harness


My schematic lies to me a lot but here it is: dark blue:goes to gauge, dark green with red stripe is pump power and black is ground.
Hot wire should have 12v, dark blue should have pulsing voltage and black should be absolute ground.

May 04, 2009 | 1993 Jeep Cherokee Country

1 Answer

I need do know what wire disconnects the computers control of the timing so i can adjust the timing and plug it back in


Disconnect the brown and black striped wire next to the heater box the wire goes up the firewall on the passenger side look right over top of the blower motor. you'll see a plug sticking out of the wiring harness loom to allow you to easily disconnect and reconnect the wire reconnect the wire when you have static timing wutxtye0rjd9d9ekmodqt1eoxkvn9hr9qjz1l3dabggyud7sdgr36czsrfxqenadhnijx9nfayi+sz1sug0aaaaasuvork5cyii=

Apr 24, 2009 | 1989 Chevrolet Camaro

1 Answer

Coil pack harness


Its important not to cross the wires in the plug if they are exposed,damage to your E.C.M.is possible.Make sure you unhook the batt. before changing anything electrical to avoid computer damage and have codes avaliable for your radio.A auto parts store willnot carry this plug,you will need to contact a auto recycling yard or salvage yard to get this plug.If you you find one ask if you can have the plug with 6-in of wire so you can either splice the wires together or try pulling each individual wire out of your old plug and put them into the new plug.Mark all wires and where they go.Write on paper.( a diagram of the wires)which wire goes where and what the color code of each wire is.Hope this helps.

Mar 04, 2009 | 2002 Volkswagen Passat

Not finding what you are looking for?
1994 Lexus LS 400 Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

Marvin
Marvin

Level 3 Expert

85108 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...