How do i program the built in garage door opener in my 1996 cheer

Instructions

1. Programming the First Transmitter
   • 1

     Unlock all of the Jeep Grand Cherokee's doors and open the driver's side door. Keeping the door open, lock it using the manual lock on the door itself.
     

   • 2

     Put the manual key into the ignition and switch it to the "On" or "Run" position, whichever applicable, without starting the engine.
     

   • Sponsored Links
     

     • Remote Control Software

       Control any distant PC remotely. Test the Software now for Free!
       www.TeamViewer.com/Remote_Control

   • 3

     Point the remote at the receiver (located by the little bulb on the car ceiling) and hold down the "Lock" button for up to 5 seconds.
     

   • 4

     When the driver's side door unlocks, you know the remote has been programmed correctly. If you are only programming one remote, jump to the next step. If not, manually re-lock the driver's side door and repeat steps 5 and 6 using each remote you would like to program and then continue.
     

   • 5

     Turn the key to the "Off" position and turn the ignition on immediately. This must be done within 20 seconds of programming the last remote. You're finished!
     

Sponsored Links

Read more: How to Program the Remote on a 1996 Jeep Grand Cherokee ' eHow.com http://www.ehow.com/how_7433787_program-1996-jeep-grand-cherokee.html#ixzz2KdCc5PQq

Instructions

1. • 1 Turn off the engine of the car and press and hold buttons 1 and 3 on the Jeep's transmitter for 20 seconds to erase previous codes. Release them when the display reads "Channels Cleared."
     
   • 2 Hold your garage-door remote 1 to 3 inches from the Jeep transmitter.
     
   • 3 Press and hold the open button on your handheld remote and simultaneously press the button you wish to program on the Jeep's transmitter. For example, if you want button 2 to be the one you use to open your garage door, press button 2 while pressing the open button the remote.
     
   • 4 Release the button once you hear a beep and the display reads "Trained."
     
   • 5 Press the "smart" button on your garage door motor. This button is usually located on the back or side of the motor near the antenna wire and light lens.
     
   • 6 Return to your vehicle and press and hold the programmed button in your Jeep for 2 seconds. Release and press and hold the button for another 2 seconds to complete the programming sequence. You will now be able to use the vehicle's transmitter to open your garage door.
     

Depends which kind of garage opener you have. But generally, it goes like this:

In car, press and hold 2 outer buttons on overhead console until indicator lights start flashing.

Hold desired button you want to program garage opener with until lights begin to flash rapidly.

At the garage door receiver in the garage, press the "learn" button. (Mine was located under one of the plastic light covers; it is purple in mine, can be other colors, but should say "learn button" or something similar) If I recall correctly, the light next to the learn button started flashing after I pressed it.

Quickly go back to the car, and press and hold the desired button and the garage should close.

That should be it.

put the key in the drivers door lock it with the key still in the lock unlock it and then pull the key out do this three times that is the factory built in security programing shut off system for jeeps and chrysler

The process is simple but too lengthy to post here.

Goto homelink.com

They make the system and have very complete instructions you can download.

PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

To program the car to your remote-hold down the 2 outer buttons until the red light blinks or comes on(not sure its been awhile) then put the garage door remote next to the sunvisor, hold down the button on the remote and any button on the sunvisor at the same time until the red light blinks. Thts it.

Hold down the button on your garage door opener while pushing one of the 3 buttons on the overhead console in the Jeep. It will beep when confirmed.

Go to dealer. Borrow a users manual. The procedure is easy. You need the handheld remote to synch the homelink to the door opener.

First you have to clear any codes in there.
Hold down the outer 2 buttons until the red light blinks, could take a minute or less.
Then release the buttons, hold your garage door opener close to the button you want to program.
hold down the button on the garage door opener and the programing button until you get a blink from the little red light. That's it