Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on Apr 01, 2012

Were is the Body Control Module on a 1994 Jeep Wrangler

5 Related Answers

Anonymous

  • 4 Answers
  • Posted on Jun 30, 2008

SOURCE: Jeep wrangler Fuse box

i had the same problem. i drive a 95 so im not sure if it differs from were the fuse box is. look righ above you pedals to your far left. it should be right there. also if you instruments went out it will be a 15 fuse. its a blue fuse. next my panel went out cuz of the wires on my transmission. if yor looking at your jeep at the front. the wires will be on your left. make sure they are not burned or anything. it will be right on the side of your tranny. mind got burned by the exaust so they were shorting. check that is and see if that is what is it. for a temp fix just put some electrical tap around the wires and you should be set for a wile. good luck

Ad

Anonymous

  • 16 Answers
  • Posted on Jan 10, 2009

SOURCE: Jeep wrangler Fuse box

You have two locations for the fuse box. One is either under the hood or behind the glove box. I would pull apart the glove box and take a look.

Anonymous

  • 2 Answers
  • Posted on Jan 10, 2009

SOURCE: BODY CONTROL MODULE

the body control module is located under the center console under shifter silver box four colored plugs

Anonymous

  • 124 Answers
  • Posted on Mar 11, 2009

SOURCE: how to change starter on 1994 jeep wrangler

is it the straight six? if so first disconnect the battery then there should be 2 bolt 13 or 14 mm. take wires off. then reverse for install.

c17hydro

Greg Bernett

  • 2993 Answers
  • Posted on Jun 23, 2009

SOURCE: try to locate body control module on a 94 buick park ave

BCM --The Body Control Module is located on the right side of the vehicle and positioned under the instrument panel. In order to gain access to the module, it will be necessary to first remove the trim panel.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2000 jeep wrangler front wiper is not working new motor and power going to the motor

The other thing that you need is a ground signal.. I believe that is supplied by the switch and the body control module on this model.
You may be money ahead to have a reputable repair facility perform the diagnostics needed to keep from "throwing" more parts at it.
1helpful
1answer

I have 2000 jeep wrangler .. cumputer light is on .. give me code says 1687

CODE P1687 - NO CLUSTER BUS MESSAGE. POSSIBLE CAUSES DATA BUS CIRCUIT SKIM TO PCM IS DAMAGED OR ITS IS OPEN. PCM UNABLE TO COMMUNICATE WITH THE BODY CONTROL MODULE. PCM HAS FAILED OR THE SKIM IS DAMAGED OR HAS FAILED.
0helpful
1answer

1988 Jeep Wrangler starting problems. I replaced the ignition module, spark plug wires, coil, distributor module, and my jeep will not start. It gets fuel, turns over, but still not starting. It is a 1988...

you are saying it is getting spark, and fuel, right? If it is getting spark, and fuel in to the throttle body, check compression-make sure the Mass Air Flow sensor is plugged in, and double check your spark-you say you replaced all those ignition items, but do not say that you have spark.
1helpful
1answer

1994 Jeep Wrangler, heater problems

Sounds like the blend door that diverts air flow inside the heater box is not working, or, the heater control valve on the heater hoses in the engine bay is not closing.
0helpful
1answer

1994 Jeep Wrangler hard to keep running

The fuel pump is located in the gas tank and the filter is right in front of the tank on the inside of the frame. I have never worked on that particular throttle body, but if it has a throttle position sensor, that could be what your problem is.
1helpful
3answers

1987 Jeep YJ Hard to start hot

Sounds like a bad distributor control module. You blew-up your muffler because there was no spark.....lots of fuel in the exhaust....then an intremittent spark......BOOM!
Once the module cools off, it works again, because the crack in the circuit board re-connects....until it gets hot again, and opens the circuit........no more spark. Replace the module.
1helpful
2answers

How to change starter on 1994 jeep wrangler

is it the straight six? if so first disconnect the battery then there should be 2 bolt 13 or 14 mm. take wires off. then reverse for install.
0helpful
1answer

No spark

Do a code check. If you can't, use a good volt/ohm meter to check components...I'd look at the ignition coil, crank sensor ign control module and all ignition related fuses. Most inexpensive manuals cover this stuff.
Not finding what you are looking for?

71 views

Ask a Question

Usually answered in minutes!

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...