1997 Jaguar XK8 Logo

Related Topics:

Kevin Kane Posted on Mar 16, 2012

1997 xk8 got engine wet, p1643, p1000

Washed engine, got p1643 and p1000 dtc codes

2 Related Answers

Anonymous

  • 1 Answer
  • Posted on Apr 22, 2009

SOURCE: failsafe engine mode light comes on, codes

Just a quick mention - for about a month my XK8 low coolant light came on intermittently. This week with no notice while driving normally I got Stability Control Fail and FailSafe Engine Mode and wtih great difficulty got the car back to where I started from (less than a mile). Two days later (when got time) and after a bit of research, I tried it again - same problem and a very unhappy engine. I then disconnected the battery for 15 minutes (probably more) to clear the engine codes as well as check all the wiring and vacuum stuff I could under the hood (at a Jaguar master mechanic's recommendation). No problems found but the car would start and immediately stall with the air intake hose disconnected from the intake butterfly. After I reconnected the air intake hose, she started and purred like normal. The problem is the BATTERY... It is low - I've known it for a LONG time BUT it always started right up and never skipped a beat. I intend to replace it tonight but fully expect that's the issue. I've had the car 6 years (it's a 98) and had NO problems except a dead taillight asembly.

Hope this is of value...

Ad

Anonymous

  • 127 Answers
  • Posted on Aug 13, 2009

SOURCE: my 97 xk8 had that stability problem. now it will not start,

code p1111 is system pass code p0333 is knock sensor 2 high input (bank 2) code p1643 is can link engine control module/transmission control modual circuit/ network also see if your car has a fuel pump shut off switch also other safety features on cars to protect against damage trans and oil fluid pressure also ckeck your neutral safety switch

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

What do codes P0411, P1000

P1000 code means the codes were cleared or the battery was disconnected
Powertrain Control Module (PCM) Reset Description All OBDII scan tools support the powertrain control module (PCM) reset.
The PCM Reset allows the scan tool to command the PCM to clear all emission-related diagnostic information. When resetting the PCM, a DTC P1000 will be stored in the PCM until all the OBD II system monitors or components have been tested to satisfy a drive cycle, without any other faults occurring. For more information about a drive cycle, refer to Drive Cycles .
The following events occur when a PCM reset is performed:
  • Clears the number of Diagnostic Trouble Codes (DTCs).
  • Clears the DTCs.
  • Clears the freeze frame data.
  • Clears diagnostic monitoring test results.
  • Resets status of the OBD II system monitors.
  • Sets DTC P1000.

P0411 Secondary Air Injection System Incorrect Flow Detected

neither of these could cause a no start or no crank problem . Is the battery good an do you have good connections on the battery ? Do the headlamps show bright when on ?
0helpful
2answers

P1000 code how do I remove this code

Hi, now it depends, I take you have a code reader? if so you should have a code reset? If the car is as you said, remove and clean injectors, I know its a pain, but as the car is not running this is the only way to clean them.
I hope this helps. What code reader are you using to know its code: P1000
0helpful
1answer

Jetta tdi problems

If you find code 18051/P1643 in the engine ECU you have to check the fault codes in the memory of the central electric computer which is VAG-COM group 09.
1helpful
2answers
1helpful
1answer

Wats the code p1000 on my 2002 jaguar x type

P1000 JAGUAR - On Board Diagnostic System Readiness Test Not Complete, this is known as the OBD2 drive cycle.


Possible causes - The vehicle is new from the factory.
- Battery or Powertrain Control Module (PCM) had recently been disconnected.
- An OBD monitor failure occurred before completion of an OBD drive cycle.
- PCM Detected Trouble Codes (DTC) have recently been cleared with a scan tool.
When is the code detected? If DTC P1000 is triggered after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles have not been cleared. P1000 JAGUAR Description The On Board Diagnostic (OBD) monitors are performed during the OBD Drive Cycle. P1000 is stored in continuous memory if any of the OBD monitors do not carry out their full diagnostic check.
1helpful
2answers

P1000 code appeared. just replaced alt. recharged batt. wont start.

The definition for P1000 code is as follows:
OBD II Monitor Testing not complete
You may be experiencing ECM computer problems. Have it diagnosed by a certified ASE professional.
1helpful
1answer

I cleared the three DTC codes previous asked, which were P0088, P0087,nad P2291, re-started the engine and getting a DTC Code P1000 can you tell me what this code is. The three previous codes started when...

P1000- on-board dianostic systems readiness test not complete, 1. obd monitors and drive cycle incomplete 2.keep alive memory(KAM) cleared, wat to do and try. remove power take off fuse(PTO) then cleared the code,disconnect pcm connector and visually check for corrosion
1helpful
1answer

My 97 xk8 had that stability problem. now it will not start,

code p1111 is system pass code p0333 is knock sensor 2 high input (bank 2) code p1643 is can link engine control module/transmission control modual circuit/ network also see if your car has a fuel pump shut off switch also other safety features on cars to protect against damage trans and oil fluid pressure also ckeck your neutral safety switch
5helpful
1answer

Failsafe engine mode light comes on, codes

Just a quick mention - for about a month my XK8 low coolant light came on intermittently. This week with no notice while driving normally I got Stability Control Fail and FailSafe Engine Mode and wtih great difficulty got the car back to where I started from (less than a mile). Two days later (when got time) and after a bit of research, I tried it again - same problem and a very unhappy engine. I then disconnected the battery for 15 minutes (probably more) to clear the engine codes as well as check all the wiring and vacuum stuff I could under the hood (at a Jaguar master mechanic's recommendation). No problems found but the car would start and immediately stall with the air intake hose disconnected from the intake butterfly. After I reconnected the air intake hose, she started and purred like normal. The problem is the BATTERY... It is low - I've known it for a LONG time BUT it always started right up and never skipped a beat. I intend to replace it tonight but fully expect that's the issue. I've had the car 6 years (it's a 98) and had NO problems except a dead taillight asembly.

Hope this is of value...
Not finding what you are looking for?

230 views

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...