Question about 2004 Hyundai Elantra

1 Answer

2004 hyundai accent flasher problem

I replaced all 4 bulbs and checked the fuse which is fine and the turn signals and the 4 ways still dont work.

Posted by on

  • Anonymous Mar 27, 2014

    Fuse locations signal hazard fuse

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 566 Answers

This sound like your flasher unit/relay is faulty as both indicators and 4 way hazard lights are not working chech your h/book for location or look under neath the fuse/relay box cover ?there is usually a diagram of location of fuses//relay

Posted on Nov 05, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2011 Ford Edge Rear Left Turn Signal not working - Bulb and Socket confirmed good. Fuse Controlling both Left Front and Rear turn light confirmed good. Front Left turn light working fine.


The flasher is under the dash.If you turn on the signal listen for it's location.Turn on your 4 way flasher and see if the left rear light is flashing.If it's not then replace the bulb.If it still does'nt work after replacing the bulb check if there is power to the socket. Use a probe light.If no power to the socket.There is a break in the wire or worse the signal switch may be the culprit

Dec 18, 2017 | Ford Cars & Trucks

2 Answers

Turn signal and brake light not working.


Change the bulb.The bulb has two lights.Running,and brake light turn signal.Its the bulb

Apr 14, 2013 | 2004 Chevrolet Silverado 1500

1 Answer

1977 trans am 4 ways and turn signals dont work the little green arrows dont even come on but when i push the breaks both little green arrows come on at the same time checked bulbs ok fuses ok but cant...


The signal flasher will be a tube about 1 inch long usually round and cylindrical it will have either 2 or three pins on it. There will be two of them and they will both be located jsut about the fuse box. swap them onis is the four way flasher one is the signal flasher. if this fixes the problem replace the bad flasher module

Feb 27, 2011 | Pontiac Trans Cars & Trucks

2 Answers

Turn signals and 4-way flashers do not work - 1997 Buick Century


Time to change the flasher unit, it's usually close to the drivers side of vehicle and behind a fuse box access panel and will have something like "12v 23/98W " on it. It's a largish cube shaped componant and may be water damaged !

Apr 10, 2010 | 1997 Buick Century

2 Answers

I have 4 way flashers but no turn signals....help!!!


there is a flasher for both 4 way & regular turn signals ( check to make sure the bulbs are good
the backs are easy >>> Just step on the brake, If the lights light up the bulbs are good you my have to remove the bulbs one at a time in the front check your ground wires to the lights if everything is good replace the flasher unit if that fails replace the turn signal switch

Feb 26, 2010 | 1990 Buick Century

2 Answers

No brake lights, turn signals, or 4-ways.


Did you actually check the bulbs? I believe your brake lights, signal lights, hazards all use the same bulb for each side.

Your brake lights may be your brake switch just above your brake pedal.
The signals could be your electronic flasher module (EFM) located under the dash near the steering column.
Your hazards may be affected by the EFM, but not likely and the switch for your hazards may be faulty

Sep 10, 2009 | 1998 Chevrolet Blazer

1 Answer

1988 ford mustang. Turn signals do not work


You did not say if its one turn signal or all turn signals that dont work. It could be a bulb.One bad bulb will cause the others not to work , normally one side of the car.Mostly left and right sides of the car is on a different circuits.
If it is all of them not working , it could be the switch in ur steering colum thats bad.Its the switch that the handle u move to turn the turn signals on and off.You would normallytake off the steering wheel to fix that switch.But its a bigger jpb , a pain.So make sure its not a bulb or a fuse first and make sure ur useing the right amp fuse.If its not that.Then id check the conection where the bulb screws into the socket.There can be corrosion there and that can cause a bad conection.Besides a bad bulb thats always been the number one reason my turn signals have not worked.You just have to keep eliminating the possibilities. Keep checking.

Mar 04, 2009 | 1992 Chevrolet Lumina

Not finding what you are looking for?
2004 Hyundai Elantra Logo

874 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...