Dtc code 300

P0450 Evaporative Emission Control System Pressure Sensor ...

www.obd-codes.com > p0450

P0450 Evap Emission System Pressure Sensor Malfunction ... This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to ...

P0450 OBD-II Trouble Code: Evaporative Emission Control ...

www.yourmechanic.com > Articles

P0450 is a diagnostic trouble code (DTC) for "Evaporative Emission Control System Pressure Sensor Malfunction". This can happen for multiple reasons and a ...

P0450 - Evaporative emission (EVAP) pressure sensor ...

www.troublecodes.net > pcodes > p0450

Nov 18, 2015 - The code P0450 is set when the ECM reads a voltage signal lower than ... DTC P0453 Evaporative Emission Control System Pressure Sensor ...

13C-DTC P0450: Evaporative Emission Control System ...

mitsubishitechinfo.com > data > HTML

DTC P0450: Evaporative Emission Control System Pressure Sensor Malfunction. CIRCUIT OPERATION. The ECM (terminal No. 114) supplies a 5 volts ...

Google your codes

The check engine light went off on it's own ? Before replacing the purge solenoid did you test the evap system by smoke checking ? Would have other code's besides P0455 if purge solenoid was bad. DTC P0455: Evaporative Emission (EVAP) System Large Leak Detected
• Inspect for a loose, missing, damaged, or incorrect fuel fill cap.
• Inspect for a damaged fuel filler neck seal surface.
• A blockage or restriction in the EVAP purge solenoid valve, purge pipe, EVAP canister, or vapor pipe, can cause this DTC to set.
• The EVAP system can be filled with smoke more quickly and completely by opening the system opposite the end where the smoke is injected. For example, when injecting smoke at the service port remove the fuel fill cap, or temporarily leave the vent open, until smoke is observed, then close the system and continue testing. If using a fuel cap adapter at the filler neck, use the J 41413-VLV at the service port to allow the system to fill faster.
• To help locate intermittent leaks using the J 41413-200 , move all EVAP components while observing smoke with the J 41413-SPT .
• Individual components can be isolated and tested using adapters in the J 41413-300 .
• A condition may exist where a leak in the EVAP system only exists under a vacuum condition. This type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the EVAP system and then observe the FTP parameter for vacuum decay.

DTC P0496
This DTC tests for undesired intake manifold vacuum flow to the evaporative emission (EVAP) system. The control module seals the EVAP system by commanding the EVAP canister purge valve Closed and the EVAP canister vent valve Closed. The control module monitors the fuel tank pressure (FTP) sensor to determine if a vacuum is being drawn on the EVAP system. If vacuum in the EVAP system is more than a predetermined value within a predetermined time, this DTC sets.
EVAP purge solenoid. maybe.

P0446 Evaporative Emission Control System Vent Control Circuit Malfunction The code P0446 is set when the engine computer recognizes a fault or restriction at the vent control part of the Evaporative emission control system (EVAP). The description of the fault varies between different car manufacturers, but one thing is common, the code P0446 doesn't directly point to a defective part; some testing might be required to pinpoint the faulty component. What can cause the code P0446: - faulty vent control valve - blockage at the vent hose, vent filter or vent control valve - open or short in the vent control valve circuit - bad charcoal canister - EVAP system leak - faulty EVAP system pressure sensor - bad vacuum switching valve (VSV) - stuck open purge valve (solenoid)

try googling for the error code

Trouble Code: P0455

Evaporative Emission (EVAP) System Large Leak Detected

Possible Causes:


A fuel fill cap that is left OFF after a fuel fill will cause this DTC to set.A loose, missing, or damaged fuel fill cap can cause this DTC to set.A blockage or restriction in the EVAP purge solenoid, purge pipe EVAP canister, or vapor pipe, can cause this DTC to set.A temporary blockage in the EVAP purge solenoid, purge pipe, or EVAP canister could cause an intermittent condition. Inspect and repair any restriction in the EVAP system.To help locate intermittent leaks, use the J 41413-200 to introduce smoke into the EVAP system. Move all EVAP components while observing smoke with the J 41413-SPT .To improve the visibility of the smoke exiting the EVAP system, observe the suspected leak area from different angles with the J 41413-SPT .Observe the Freeze Frame/Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition occurs that caused the DTC to set . This may assist in diagnosing the condition.

DTC P0496 - EVAPORATIVE EMISSION (EVAP) SYSTEM FLOW DURING NON-PURGE

SYSTEM DESCRIPTION
This DTC tests for undesired intake manifold vacuum flow to the evaporative emission (EVAP) system. The control module seals the EVAP system by commanding the EVAP canister purge valve Closed and the EVAP canister vent valve Closed. The control module monitors the fuel tank pressure (FTP) sensor to determine if a vacuum is being drawn on the EVAP system. If vacuum in the EVAP system is more than a predetermined value within a predetermined time, this DTC sets.

THIS CODE ID FOR A 3.6L engine

Your best bet take it to a qualified repair shop . It takes special tool's to diagnose evaporative emission system's .
DTC P0411 : Secondary Air Injection (AIR) System Incorrect Air Flow Detected
DTC P0449: Evaporative Emission (EVAP) Vent Solenoid Control Circuit
DTC P0455: Evaporative Emission (EVAP) System Large Leak

From web page that follows. This DTC tests for undesired intake manifold vacuum flow to the evaporative emission (EVAP) system. The control module seals the EVAP system by commanding the EVAP canister purge valve Closed and the EVAP canister vent valve Closed. The control module monitors the fuel tank pressure (FTP) sensor to determine if a vacuum is being drawn on the EVAP system. If vacuum in the EVAP system is more than a predetermined value within a predetermined time, this DTC sets.

http://www.hotrodlane.cc/New%20LS%20Links%20Page/LS%20trouble%20codes/DTC%20P1441.htm