Adjust headlamp on 2001 chevrolet tracker

Question edited for clarity.

Better if done by garage with an aiming board, but some help here.

https://www.google.com/search?q=2000+Chevrolet+Tracker.+How+to+adjust+headlight+beam

..

Get flat screwdriver and star screwdriver

menu

How to Adjust a Headlamp Beam on a 2005 Chevrolet Cavalier...

When you replace the headlamp assembly in the 2005 Chevrolet Cavalier, you must also adjust the headlamp beams. Like most vehicles, there are two screws located on the headlamp assembly that control the vertical and horizontal direction of the headlamps. Proper adjustment is necessary for adequate visibility during nighttime driving; bad adjustment can make it difficult for you to see or make it difficult for oncoming drivers to see, creating a potentially dangerous situation. You can adjust the headlamp beams yourself with a screwdriver in about 15 minutes.
Park the Chevrolet Cavalier on a flat surface facing a wall or garage door approximately 15 feet away. Park the Car so that it is perpendicular to the wall.

Lift the hood and remove the plastic trim panel above each of the headlights. There are three plastic fasteners that secure the trim panel; pry the fasteners out using a flathead screwdriver. Lift the trim panel up to remove. There are two adjusting screws beneath the trim panel, one on the top of the headlamp assembly and one along the outer side of the headlamp assembly.

Turn the headlights on so that they shine on the wall. Ensure the headlights are on the "dim" setting.

Adjust the vertical bolt, located on the top of the headlight assembly near the center of the vehicle to raise or lower the headlight, using a crosspoint screwdriver. Turn the screw counterclockwise to lower the headlamp beam; turn the screw clockwise to raise the headlamp beam. Adjust the headlamp so that the beam is below a driver's eye level.

Adjust the horizontal bolt, located on the outer side of the headlamp assembly to move the headlamp beam right of left, using a crosspoint screwdriver. Turn the screw counterclockwise to move the headlamp beam right; turn the screw clockwise to turn the beam left. Adjust the headlamp so that the beam shines straight ahead or slightly toward the center of the vehicle.

Replace the plastic trim panel and fasteners and close the hood. Warning: raising the lights too high can make it difficult for other drivers to see you.

Headlight relay #1 location? - Suzuki Forums: Suzuki Forum Site

www.suzuki-forums.com/...geo.../34499-headlight-relay-1-location.html

Nov 12, 2009 - 10 posts - ‎2 authors
After testing everything else, the headlight relay #1 is the main suspect. Where ... Geo Tracker .... then walk the red lead from the fuse to HL Headlights stay ON - 2001 Chevy Tracker
10 posts
May 10, 2013
2003 tracker: Fuse & relay locations
10 posts
Jul 18, 2011
Disconnected DRL module from Tracker/Vitara 2002, but ...
10 posts
Oct 1, 2010
Disabling DRL
10 posts
Sep 5, 2009
More results from www.suzuki-forums.com

Interior Fuse Box Location: 1999-2004 Chevrolet Tracker ...

www.carcarekiosk.com/video/...Chevrolet_Tracker_2.../fuse.../replace

The video above shows how to replace blown fuses in the interior fuse box of your 2000Chevrolet Tracker in addition to the fuse panel diagram location.

Painless Headlamp Relay for 1999 - 2002 Chevy T

How to adjust the headlights on an 86 jeep Comanche - Fixya

www.fixya.com/cars/t26003692-adjust_headlights_86_jeep_comanche

9 mins ago - Do you mean Aftermarket or Factory Harness ... it sounds more like a faulty headlight switch assembly ... Buy a new one at a parts store, install it.

Headlamp Adjusting Screw - Sold Individually - 55054621

www.morris4x4center.com/headlamp-adjusting-screw-55054621.html

Rating: 5 - ‎5 votes
1984-2001 Jeep XJ Cherokee; 1986-1992 Jeep MJ Comanche. Description: This is aHeadlamp Adjusting Screw. This allows you to aim your headlights ...

Headlight adjustment - Jeep Cherokee Forum xjTalk - A Jeep podcast!

xjtalkshow.com/showthread.php?t=13045

Jan 7, 2013 - Headlight adjustment OEM/Factory. ... the JEEP TALK SHOW! It's aJEEP podcast! iTunes, Stitcher, TuneIn or... http://jeeptalkshow.com ...

Adjusting headlights - JeepsUnlimited

is it a plastic lens AERO haedalmp or rectangular glass?

SECTION 417-01: Exterior Lighting 2001 F-Super Duty/Excursion/Motorhome Chassis Workshop Manual
REMOVAL AND INSTALLATION Lamp Assembly -Headlamp, Aerodynamic Removal and Installation

1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
   Remove the headlamp assembly.
   1. Pull up and remove the two upper headlamp clips.
   1. Release the lower headlamp clip.
   1. Position the headlamp so the electrical connector can be accessed.
   1. Disconnect the headlamp electrical connector.

1. To install, reverse the removal procedure.
   • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

Headlights? The horizontal adjusting screw is on the inside - behind the headlamp and the vertical adjusting screw is on the outside (fender side). The idle is controlled by the computer.

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

If you have one adjustment screw, it will control your vertical aim. If you have two adjustment screws, one will control your vertical aim and the other will control your horizontal aim

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Removal & Installation To Remove:

1. Remove or disconnect the following:
   • Hood close out filler panel.
   • Bolts from the headlamp.
   • Headlamp from the headlamp mounting panel.
   • Electrical connector from the headlamp.
   • Headlamp bulb/socket retainer ring from the headlamp.

Headlamp bulb/socket from the headlamp.

Bolts from the headlamp adjuster mechanism.

Headlamp adjuster mechanism.

To Install:

1. Install or connect the following:
   • Headlamp bulb/socket to the headlamp.
   • Headlamp bulb/socket retainer ring to the headlamp.
   • Headlamp adjuster mechanism to the headlamp housing, if necessary
   • Bolts to the headlamp adjuster mechanism. Tighten to 6 N.m (53 lb in).
   • Electrical connector to the headlamp.
   • Headlamp to the headlamp mounting panel and lower mounting bracket.
   • Bolts to the headlamp. Tighten to 10 N.m (89 lb in ).
   • Hood close out filler panel.

there is a cover on the backside of these just pull of or twist off then replace the headlamp/ Please rate my response thank you very much

We have a 2001 Tracker. I believe that I did replace a headlight - it's really just a fancy BULB that I think twists-out of the housing from the rear. Pretty sweet not having to pull a big old glass headlamp. Do not touch the new bulb with your bare fingers as the skin oils can shorten the life of the bulb. To change the shell of the headlight - probably similar to most vehicles - look around with a flashlight and locate the screws/clips that may be present. Some of these may be "Torx" type. You may or may not need to remove the ADJUSTMENT screws. Avoid this if possible, otherwise the light will be out of alignment and will drive you or other drivers crazy.