2001 chevy tracker how to get blower moter out

SOURCE: 2001 chevy k1500 4wd front u joint failed

Changing Universal joints is an art. First, to make it easy, you need a pretty large vice. C-clamps can work if you are man enough to sqeeze them, sometimes a lot of pressure is involved and it gets hard to hold all parts in place. A vice is recommended, or a press of some sort.
You need a socket or pipe cap big enough to slide over the diameter of a single u-joint cap. Take the driveshaft and lay it in the jaws of the vice, so the U-joint is in the squeeze zone. take a socket smaller than the cup diameter and place it on one side. Take the large socket and place it on the other side of the u-joint. tighten vice. The small socket will push the U-joint through the yolk, and push the opposite cap into the empty space of the large socket. Once you bottom out, remove from the vice, and take off the cap you just pushed through. ( You may need a pair of vice grips to grab and twist the cap the rest of the way out.) Now, put giant socket over cap that is still in the yolk, place the small socket so it presses on the capless side of the U-joint Squeeze vice, so the existing cap gets pushed back through where it came from, but then keep squeezing until it is out of the yolk and pressed all the way to the large socket side. Once there, remove from vice, pull the now pressed out second cap out of the yolk hole. Now both caps are off, and you can just pull U-joint out of yolk.
Putting the new one back in is tricky too, you must remove both new caps and put capless U-joint back in hole of yolk, place a samall amount of fresh grease into caps to hold needle bearings in place. (if needle bearing falls out of place and you squeeze the U-joint back together, it will snap or bend bearing and U-join is no good, you must get another needle bearing to replace the damaged one, maybe salvage from old joint, but best to buy new joint if this happens, but if 11:00 pm and store is closed, you have to work next morning, then steal one from old joint) then slide both caps in from outside at same time, while twisting yolk squeeze in caps with vice. Once you bottom out on both sides, take small socket and press one side in until ring acan snap in, not too far, just enough to get ring in, then press in opposite side to same point. Put in rings clamps, then wiggle side to side for free movement. Then install back into truck.

SOURCE: how does the squirrel cage come off of the blower

Most units are one unit. Motor and squirel cage. A machine is used to press the cage onto shaft. Otherwise shaft bolt should have hexagontal nut end if it is removable.

Testimonial: "The new blower come,s without the cage.So I will have to somehow get it off the shaft without breaking it.I can,t buy the cage at an auto parts store."

SOURCE: 4wd wont work on 1999 chevy tracker but front drive shaft is turning?

The locking hub control system is not engaging properly. On the 99 Tracker this is a compressed air system that consists of an air pump (compressor), electrical wiring to power and control the air pump, and air hoses that lead to an actuator inside the front differential housing. If there is a leak in the system the PCM will run the air pump for 10 seconds and then shut off, and your propeller shaft can turn all day long, but the front axles will remain free floating. Turn on your key, not your engine, and engage four wheel high. Go listen near the passenger front bumper for the air compressor. If you hear it, then the compressor control and the compressor itself are likely fine. If it shuts off after 10 secs or so, and your 4WD light isn’t on, the PCM timed out the compressor out and shut the compressor off to protect it. You will have to find the leak and fix it. If you are lucky, it’s the air line leading to the front differential; and not the air line inside the differential housing, or the air bladder in the locking actuator, which also resides inside the font diff. If the compressor shuts off and the 4WD light is on (this means the PCM did not shut the air compressor off due to timeout, so the pressure switch read 5-7 psi and the pump shut itself off), you likely don’t have a leak, and something mechanical has the actuator hung up inside the front differential. Lastly if you don't hear the compressor run at all, you either have a faulty compressor, or some sort of wiring problem in that circuit.....it could be as simple as a blown fuse. Good luck.

SOURCE: Front blower motor on 2005 dodge caravan not working

Used the bulletin board - swapped out the resistor and it works now.
Thanks for the bulletin boards...

Testimonial: "1 problem; 1 solution; 1 fix...great work!!!"

SOURCE: 2006 dodge ram 2500 diesel ac damper above blower

2006 dodge 2500 diesel. low voltage at compressor.