Program key remote - 2005 Hyundai Elantra

you can't bypass computer set software. You can however reprogram the key transponder and receiver. If you have NO working key, you need the dealership.

2007 Chrysler PT Cruiser

1. Insert First Programmed Key. INSERT a working remote head key into the Ignition and TURN it to the ON/RUN position.
2. Remove First Programmed Key. ...
3. Insert Second Programmed Key. ...
4. Remove Second Programmed Key. ...
5. Program Remote. ...
6. Program Additional Remote. ...
7. Exit Programming Mode. ...
8. Test Remotes.

More items...

2007 Chrysler PT Cruiser Keyless Entry Remote Fob ...

Procedure #1 (Remote Head Keys WITH Immobilizer Chip)
Step-by-Step How To Programming Instructions:

1. CUT the NEW remote head key for your vehicle.
2. INSERT the first working remote head key into the Ignition.
3. TURN the Ignition to the ON position for at least three (3) seconds but no longer than fifteen (15) seconds.
4. TURN the Ignition to the OFF position and remove the first remote head key.
5. INSERT the second working remote head key into the Ignition.
6. TURN the Ignition to the ON position for at least three (3) seconds but no longer than fifteen (15) seconds.
7. After ten (10) seconds a chime will sound and the vehicle's security light will begin to flash.
8. TURN the Ignition to the LOCK position and REMOVE the second remote head key.
9. INSERT the NEW remote head key into the Ignition.
10. TURN the Ignition to the ON position within 60 seconds.
11. After ten (10) seconds a single chime will sound and the vehicle's security light will stop flashing.
12. The vehicle's security light will turn ON again for three (3) seconds and OFF to indicate successful programming.
13. Test all remotes. Programming is now complete. The remote and key are now both programmed.
14. If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

Procedure #2 (Remote Head Keys WITHOUT Immobilizer Chip)
Step-by-Step How To Programming Instructions:

1. ENTER the Vehicle and CLOSE all doors.
2. INSERT key into Ignition.
3. TURN the Ignition to the ON position (before cranking).
4. PRESS and HOLD UNLOCK on a working remote head key for four (4) to ten (10) seconds.
5. WHILE holding the UNLOCK button, PRESS the PANIC button UNTIL a chime sounds to indicate entry into Programming Mode.
6. RELEASE both the PANIC and UNLOCK buttons.
7. PRESS the LOCK and UNLOCK buttons simultaneously on the same remote until a chime is heard.
8. Once the chime is heard, PRESS and RELEASE the UNLOCK button on that same remote. Another chime will sound indicating successful programming of that remote. (This MUST be done within 30 seconds)
9. WITHIN 30 seconds of Step 8, PRESS the LOCK and UNLOCK buttons on any other remotes to be programmed. RELEASE the buttons when the chime is heard. Again, PRESS and RELEASE the UNLOCK button on that remote. Another chime will sound indicating successful programming of that remote.
10. REPEAT Step 9 for ALL remotes (even working remote head keys) that you want to work with your Vehicle.
11. Test all remotes. Programming is now complete. The remote and key are now both programmed.
12. If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

Hope one of these helps.

2006 Buick Rendezvous Remote Programming For Buick Rendezvous / Intrigue / AztekObtain all remote transmitters for this vehicle.
1. Close all doors.
2. Press and hold the Unlock button on door lock switch on drivers door.
Hold until instructed to release in step 6.
3. Insert key into the ignition cylinder but do not turn it.
4. Remove key from ignition and then insert key into ignition without turning ignition cylinder and remove key.
5. Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.
6. Release door lock switch on drivers door panel. A Chime will sound 3 times indicating that you are in programming mode.
7. Press both the Lock and Unlock buttons on the remote up to 30 seconds.
A chime will sound 2 times if remote has programmed successful.
8. Repeat step 7 if you are programming additional remotes.
9. Remove key from ignition to exit programming mode

Keyfob remote reprogramming is not very difficult but on some cases it can be done by dealer service tools.If the remote s faulty then keyfob will not get programmed.Insert the key in ignition.Turn the key to on position,and cycle the key three times off-on-off-on-off-on.Then with the keyfob remote select your remote and then try to operate the vehicle with remote.These is just the basic procedure,but sometimes it will not help.
On that case dealer is the only option.
---------There are few very relted troubleshooting links mentioned below for remote key fob reprogramming.I suggest you to go through the list and click the link below to go through its details and procedure:-------
2009 Toyota Highlander: Smart Key Not getting Detected? http://whatisbyme.blogspot.in/2012/05/2009-toyota-highlander-smart-key-not.html
----------2007 Toyota Prius: Reprogram Remote Keyfob? http://whatisbyme.blogspot.in/2012/05/2007-toyota-prius-reprogram-remote.html
----------- Pin that holds the flick key part to the key fob? http://whoisbyme.blogspot.in/2012/07/pin-that-holds-flick-key-part-to-key-fob.html
-------------
2006 Toyota Hilux: Programming New Key? http://technoanswers.blogspot.in/2012/04/2006-toyota-hilux-programming-new-key.html
----------Where is Key chip memory located on 2004 ford Freestar? http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html
----------Ford Keyless Remote Fob Reprogramming?

http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html
----------After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure? http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html
-----------Audi A8 Key Fob Programming?

http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html

----------------
Oldsmobile Aurora Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html

-------------
Buick Lesabre Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html

---------------
Keyfob remote not working on 2003 Ford E350 Econoline?

http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html

-----------
KeyFob will open the doors but not start on BMW?

http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html

------------
Mitsubishi Car Key Not getting detected after replacing ECM http://repairhelpcenter.blogspot.com/2012/11/mitsubishi-car-key-not-getting-detected.html
----------- Key Fob will not lock and unlock doors?

http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html

-------------
2000 Jeep Cherokee Limited: KeyFob Remote Not Working? http://schematicsdiagram.blogspot.in/2012/06/2000-jeep-cherokee-limited-keyfob.html
----------- Chevrolet Malibu: Key Stuck in ON position? http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html
----------- Theft indicator not letting car to start?

http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html

-------------
2012 Dodge Ram: Ignition Key will not release? http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html
--------------
These details will help.Thanks.

If you don't have the Panic button then sorry, you can't program yourself, the dealer will have to program it to the RKE (Remote Keyless Entry) module in the vehicle, using their DRB scan tool.

Obtain all keys/remote controls. Remove driver's side kick panel/lower 'A' pillar trim. Connect central locking registration connectors (white) - black wire and black/blue wire Fig. 2 . Unlock the vehicle using the key. Program first key/remote control as follows: Press unlock button Fig. 1 [1], then lock button [2]. The door lock should lock and unlock in sequence confirming programming of first key/remote control. Repeat programming procedure for remaining key(s)/remote control(s). Once the last key/remote control is programmed disconnect central locking registration connectors. Check operation of all programmed keys/remote controls.

The 1997 to 2003 Dodge Caravan and Grand Caravan use a standard key and remote setup with a separate remote fob. However, the 2004 to 2009 Dodge Caravan and Grand Caravan use a combination key and remote on one device. To program a new keyless entry remote for the 1997 to 2003 Dodge Caravan, you must have at least one functional remote, which is required to enter synchronization mode. To program the combination key for the 2004 to 2009 Dodge Caravan, you must have two functional combination keys. If you do not, you'll need to see an authorized Dodge dealer for keyless entry programming assistance.


2004 to 2009 Caravan Programming Instructions

1. Insert one of your working combination keys into the ignition. Turn it to "On"; leave it in this position for about 10 seconds but no longer than 15 seconds. Turn it to "Off" and remove it.
   
2. Insert your second working combination key into the ignition within 15 seconds of removing the previous key. Turn it to "On". After 10 seconds, you'll hear a chime and the "Theft" light will begin to flash, entering synchronization mode. Turn the key to "Off" and remove it.
   
3. Insert the combination key you want to program. Turn it to "On." After 10 seconds, you'll hear a chime; then the "Theft" light will turn off. When the light turns off, the combination key--including the key and the remote--is programmed.
   
4. Repeat Step Three for each combination key you want to program. A total of eight can be programmed.

Hope this help (remember comment and rated).

Use this Procedure for Vehicles with
Driver Information Center Buttons

This information is in your Owners Manual in the
Drivers Information Center Section.

1. Insert Key and turn to ON position so you can access Driver Information Center

2. Press the vehicle information button until
PRESS TO RELEARN REMOTE KEY displays

3. Press the set/reset button until
REMOTE KEY LEARNING ACTIVE displays

4. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximatley 15 seconds. A chime will sound indicating that the remote is
programmed.

5. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.
6. To exit programming mode turn key off and remove key.
Test remote(s).

Use this Procedure for Vehicles without
Drivers Information Center Buttons
To access this display, the vehicle must be in Park (P) with key in the on position (as far
as you can go without cranking engine)

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
2. Press and hold the trip odometer reset stem for three seconds.
The message REMOTE KEY LEARNING ACTIVE will display
3. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.
4. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.
5. To exit programming mode turn key off and remove key.
Test remote(s).


Good luck and hope this helps, you may have to reprogram. merry Xmas

Use this Procedure for Buick Vehicles "With" Driver Information Center Buttons.

This information is in your "Owners Manual" in the "Drivers Information Center Section."

1. Insert Key and turn to ON position so you can access Driver Information Center.

2. Press the vehicle information button until PRESS TO RELEARN REMOTE KEY displays.

3. Press the set/reset button until REMOTE KEY LEARNING ACTIVE displays.

4. Press and hold the lock and unlock buttons on the key-less remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.

5. To program additional remotes at this time repeat step 4. This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn key off and remove key. Test remote(s).


Use this Procedure for Buick Vehicles "Without" Drivers Information Center Buttons.

To access this display, the vehicle must be in Park (P) with key in the on position (as far as you can go without cranking engine).

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.

2. Press and hold the trip odometer reset stem for three seconds. The message REMOTE KEY LEARNING ACTIVE will display

3. Press and hold the lock and unlock buttons on the first key-less remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.

4. To program additional remotes at this time repeat step 3. This vehicle can have a maximum of eight remotes programmed.

5. To exit programming mode turn key off and remove key. Test remote(s).

Good Luck !

This is the procedure for a reprogram of the remote's from the factory service manual, if it doesn't work then u may have a receiver issue.
Use this Procedure for Vehicles with
Driver Information Center Buttons

This information is in your Owners Manual in the
Drivers Information Center Section.

1. Insert Key and turn to ON position so you can access Driver Information Center

2. Press the vehicle information button until
PRESS TO RELEARN REMOTE KEY displays

3. Press the set/reset button until
REMOTE KEY LEARNING ACTIVE displays

4. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximatley 15 seconds. A chime will sound indicating that the remote is
programmed.

5. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.
6. To exit programming mode turn key off and remove key.
Test remote(s).


Use this Procedure for Vehicles without
Drivers Information Center Buttons

To access this display, the vehicle must be in Park (P) with key in the on position (as far
as you can go without cranking engine)

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
2. Press and hold the trip odometer reset stem for three seconds.
The message REMOTE KEY LEARNING ACTIVE will display
3. Press and hold the lock and unlock buttons on the first keyless remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.
4. To program additional remotes at this time repeat step 3.
This vehicle can have a maximum of eight remotes programmed.
5. To exit programming mode turn key off and remove key.
Test remote(s).