2007 Jaguar XKR Convertible Logo

Related Topics:

A
Anonymous Posted on Feb 19, 2012

Replace Brake Lamp Jaguar XKR - 2007 Jaguar XKR Convertible

4 Related Answers

Anonymous

  • 10 Answers
  • Posted on May 02, 2009

SOURCE: how to replace brake lamp in jaguar s type 2002

open the trunk and pull back the carpet and there should be wire harnesses going to the lamps turn them clockwise or counter clockwise and they should release then have someone use the brakes to find which one is burnt out and replace it then put everything back in the way it was taken out

Ad

Anonymous

  • 9 Answers
  • Posted on May 30, 2009

SOURCE: replace cabin pollen filter 2005 jaguar xkr

To get to the cabin air filter on an XK8 or XKR, you have to do the following steps (I know these steps sound ridiculous...as in many cars there is just a simple cover in the engine compartment... but...): The air filter is under the black plastic cowl or plenum that is just under the windshield wiper blade connectors. To get to that, you must 1. carefully lift off the plastic covers that reveal screw heads. Remove the screws. 2. lift off the plastic covers that are on the top of each windshield wiper connector - under the cover you will then see a nut or bolt that has to be unscrewed. 3. Using a small puller (the puller that lifts off battery terminals works for this) lift off each windshield wiper and disconnect the rubber hose from each. 3. lift the car's front hood, and remove the plastic cowling (you also have to lift the side rubber runners and a rubber strap from each side that holds up the rubber drain hoses). Once you remove that plastic cowling, you will see the air filter plenum at the back of the engine area. The air filter should come vertically out of that. (This air filter does not exist on my 2000 and earlier editions...I am not sure what year Jaguar installed them.) Full instructions are on the Jaguar JTIS CD which you should obtain...look online for that.

Anonymous

  • 4088 Answers
  • Posted on Oct 12, 2009

SOURCE: parking brake on 2000 jaguar

There are two cables in housings that come from the rear wheels and are exposed to water from the road which results in rusted cables and interiors of the housings. Replace both parts on each side. Make sure that you get new rubber boots for the open ends of the cables.

Mike

  • 4383 Answers
  • Posted on May 30, 2010

SOURCE: brake lamp failure Jaguar XK 2007

Replace the lamps

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
2helpful
1answer

Battery disconnected and accidentally closed trunk. cannot open now. how do we open manually?

there is a manual keyhole in the XKR badge below the right hand rear lamp cluster
0helpful
1answer

2002 Jaguar xj8 When I step on the brake pedal

check all the lights on the back of the car there must be a bulb burned out
2helpful
1answer

Parking brake on 2000 jaguar xkr won't release but moves freely

There are two cables in housings that come from the rear wheels and are exposed to water from the road which results in rusted cables and interiors of the housings. Replace both parts on each side. Make sure that you get new rubber boots for the open ends of the cables.
2helpful
2answers

Parking brake won't release but hand lever moves freely

Hi

Thanks for using FixYa. In Jaguar XKR the parking brake is controlled electronically unlike the cable ones. The voltage applied to the electronic Park Brake module is applied at the same time you start the engine, consequently on a very cold day the battery will be far less efficient and due to the extra power required to start a very cold 6 cylinder engine the voltage will fall.

Although this reduced voltage will quite happily start the car it will trip out the Parking brake. To help avoid this problem happening again switch the ignition to position 2(position just prior to starting) and press the chrome handbrake tab down while having your foot on the brake. The brakes will be released, the park brake light on the dash will go out and you can now start the car.

On the new XKR module the electronic handbrake is not activated by the gear shift as in the later S models so you can start the car and then release the brake when the engine is running.

Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks

Rylee
0helpful
1answer

Need to replace light on jaguar xkr 2003

At
www.reliable-store.com
get complete guide on whether to repair or not, service it, and how to repair
etc, along with wiring diagrams, electrical diagrams, torque specs, error codes, everything.
9helpful
1answer

Replace cabin pollen filter 2005 jaguar xkr

To get to the cabin air filter on an XK8 or XKR, you have to do the following steps (I know these steps sound ridiculous...as in many cars there is just a simple cover in the engine compartment... but...): The air filter is under the black plastic cowl or plenum that is just under the windshield wiper blade connectors. To get to that, you must 1. carefully lift off the plastic covers that reveal screw heads. Remove the screws. 2. lift off the plastic covers that are on the top of each windshield wiper connector - under the cover you will then see a nut or bolt that has to be unscrewed. 3. Using a small puller (the puller that lifts off battery terminals works for this) lift off each windshield wiper and disconnect the rubber hose from each. 3. lift the car's front hood, and remove the plastic cowling (you also have to lift the side rubber runners and a rubber strap from each side that holds up the rubber drain hoses). Once you remove that plastic cowling, you will see the air filter plenum at the back of the engine area. The air filter should come vertically out of that. (This air filter does not exist on my 2000 and earlier editions...I am not sure what year Jaguar installed them.) Full instructions are on the Jaguar JTIS CD which you should obtain...look online for that.
0helpful
1answer

Replaced brake pads, extreme squeal resulted

Pads will reproduce sound just like a needle on a phonograph. Hard linings will accentuate this. Have the rotors re-surfaced and finished with a non-directional pattern(I make a quick pass with a D/A sander over surfaces while still on the lathe) Generally this will help.
Not finding what you are looking for?

298 views

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...