Belt routing - 2000 Honda Civic

Here is the serpentine belt routing for a 2013 VW CC with a V6 3.6 liter engine:

1. Start by locating the automatic belt tensioner on the front of the engine.
2. Route the belt around the crankshaft pulley at the bottom of the engine.
3. From there, route the belt around the idler pulley, which is just above the crankshaft pulley.
4. Next, route the belt around the alternator pulley, which is located on the top left side of the engine.
5. After the alternator, route the belt around the power steering pump pulley, which is located on the top right side of the engine.
6. From there, route the belt around the water pump pulley, which is located just above the power steering pump.
7. Finally, route the belt around the tensioner pulley, which should be the last pulley in the belt routing.

Double-check that the belt is properly seated on each pulley and that the routing matches the diagram on the engine or in the owner's manual before starting the engine.

I need a belt routing diagram for an o 06 Duramax with air ps etc

It depends on the engine size for the belt routing.

Click on the "x" for the diagrams on the following engine sizes:
FIRING ORDER AND BELT ROUTING Firing Order and Belt Routing X90, Vitara & Grand Vitara Fig. 1: 1998 1.6L engine Firing order: 1-3-4-2 Distributor rotation: Counterclockwise
Fig. 2: 1999-02 1.6L engine Firing order: 1-3-4-2 Distributorless ignition system (coils over No. 2 and 4 cylinders)
Fig. 3: 2.0L engine Firing order: 1-3-4-2 Distributorless ignition system (one coil over each cylinder)
Fig. 4: Accessory V-belt routing- 1.6L engine with A/C
Fig. 5: Accessory V-belt routing-1.6L engine with A/C and P/S
Fig. 6: Accessory V-belt routing-1.6L engine with P/S
Fig. 7: Accessory serpentine belt routing-1.8L and 2.0L engines
Fig. 8: Accessory V-belt routing-1.8L and 2.0L engines
Fig. 9: Accessory V-belt routing-2.5L engine with P/S
Fig. 10: Accessory V-belt routing-2.5L engine with A/C and P/S

Depends on engine. Copied below diagrams from AutoZone.com:

Drive Belt Routings




Fig. Accessory drive belt routing-2.4L engine



Fig. Accessory drive belt routing-2.7L (3RZ-FE/M) engine



Fig. Accessory drive belt routing-2.7L (2TR-FE) engine



Fig. Accessory drive belt routing-3.4L engine

Fig. Accessory drive belt routing-2.4L engine







Fig. Accessory drive belt routing-2.7L (3RZ-FE/M) engine








Fig. Accessory drive belt routing-2.7L (2TR-FE) engine








Fig. Accessory drive belt routing-3.4L engine







Fig. Accessory drive belt routing-4.0L engine

Hope helps (remember rated this).

Fig. Serpentine accessory drive belt routing-3.0L (VIN U) engine


Fig. Serpentine accessory drive belt routing-3.0L (VIN S) engine


Fig. Serpentine accessory drive belt routing-Ford 3.0L (VIN U) engines


Fig. Serpentine accessory drive belt routing-Ford 3.0L (VIN S) engine


Fig. Serpentine accessory drive belt routing-Ford 3.4L SHO engine


Fig. Water pump drive belt routing-Ford 3.4L SHO engine
i wasnt sure what engine you had hope this helps good luck

Like a lot of people...you didn't post your engine size....so out of these 11 photos, please choose the correct one for your application:


Accessory drive belt routing—1.8L (AEB/ATW/AWM) engines


Accessory drive belt routing—1.8L (AWP/AWV/AWW) engines 2.0L (AEG/AVH/AZG/BDC) engines without A/C


Accessory drive belt routing—1.9L diesel (ALH) engines without A/C


Accessory drive belt routing—1.9L diesel (ALH) engines with A/C


Accessory drive belt routing—1.8L (AWP/AWV/AWW) engines 2.0L (AEG/AVH/AZG/BDC) engines with A/C


Accessory drive belt routing—2.0L (ABA) engine without A/C


Accessory drive belt routing—2.0L (ABA) engine with A/C


Accessory drive belt routing—2.5L (BGP) engine with A/C


Accessory drive belt routing—2.8L (AFP/BDF) engines


Accessory drive belt routing—2.8L (ATQ) engines


Accessory drive belt routing—4.0L (BDP) engine

You didn't list your motor size so please pick the applicable diagram:


Accessory serpentine belt routing—4.8L, 5.3L & 6.0L engines


Accessory serpentine belt routing—5.7L engines with A/C


Accessory serpentine belt routing—5.7L engines without A/C


Accessory serpentine belt routing—6.5L Diesel engines


Accessory serpentine belt routing—7.4L engines


Accessory serpentine belt routing—8.1L engines

2003 Hyundai Tiburon 2.7L MFI DOHC 6cyl

Inspection
Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.
Removal & Installation

1. Raise and support the vehicle.
2. Remove the engine splash shield.
3. Rotate the drive belt tensioner clockwise to release the drive belt tension.
4. Remove the drive belt from the alternator.
5. Slowly release the drive belt tensioner.
6. Remove the drive belt from the accessory drive pulleys.

To install:

1. Install the drive belt to the accessory drive pulley.
2. Rotate the drive belt tensioner clockwise.
3. Install the drive belt to the alternator.
4. Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.
5. Slowly release the drive belt tensioner
6. Install the engine splash shield.
7. Lower the vehicle.

Fig. Accessory drive belt routing-3.0L and 3.5L engine




Fig. Accessory drive belt routing-2.5L and 2.7L engines




Fig. Accessory drive belt routing-2.4L engines




Fig. Accessory drive belt routing-2.0L engines




Fig. Accessory drive belt routing-1.5L engine




Fig. Accessory drive belt routing-3.0L engine




Fig. Accessory drive belt routing-2.5L engines




Fig. Accessory drive belt routing-2.4L engines




Fig. Accessory drive belt routing-1.8L and 2.0L engines




Fig. Accessory drive belt routing-1.5L engine




Fig. Accessory drive belt routing-2.4L engines




Fig. Accessory drive belt routing-2.0L engines




Fig. Accessory drive belt routing-1.5L engine


I hope help you with this (remember rated this help) Good luck.