Astrostart 2100 autostart will not work all the time

jump start the car.
Battery might not be strong enough to crank the engine

[PDF]MODEL RSS-5225 - DirectedDealers.com

www.directeddealers.com/manuals/OG/Astrostart/RSS-5225_OG-Eng.pdf

Immediately report any malfunction to the AstroStart dealer that performed the ... Always turn off the main switch when not using the remote starter for .... The startmodule will inform you of the status of door locks, the alarm and of the engine. .... If the trunk is opened for more than 5 minutes, the system switches to the.

How do you reprogram an AstroStart remote HST5224

www.answers.com > Wiki Answers > Categories > Cars & Vehicles

In order to reprogram an AstroStart HST5224 remote, you must putthe key in the ignition ... lamp) b, press and hold UNLOCK button, after 1 second key LED will flash once c, .... C. Turn the ignition to ON (Do NOT Start) then back to OFF. ... B.Immediately after letting go of the lock and unlock buttons, press the lock button by ..

Get under the dash or where the unit is located.
You will see 8 or 9 dip switches on the unit with an LED beside them.
Turn switch 1 and 8 on.
Press and release the brake. (LED will flash)
Press and hold start button on remote. (LED will flash and parklights will flash once.
Turn switch 1 and 8 to off.
Press and release the brake (LED will flash once)
In future would be a good idea to supply vehicle details etc as can sometimes be a known condition , that saves time looking it up , good luck

You may need to reset the system.

SEQUENCE ACTIVATED BY THE PARKING BRAKE .
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply the parking brake Once Twice
Note: The system can be set - at time of installation - to require that the parking brake be applied once or twice.
If set for two actuations, pause one second between the two.
4. Remove key from ignition (the system keeps the engine running).
5. Exit the vehicle.
6. Within 60 seconds, close all doors.
7. The system will stop the engine and blink the parking brakes once to confirm the sequence is valid (vehicle is
ready for a remote start command).
SEQUENCE ACTIVATED BY THE REMOTE CONTROL
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply parking brake.
4. Send the start command (Model 801 & 2101 - Model 903 ).
5. Remove key from ignition (the system keeps the engine running).
6. Exit the vehicle.
7. Using the remote, send the STOP command. The system will stop the engine and parking lights will blink once
to confirm that the sequence is valid (vehicle is ready for a remote start command).
http://www.astrostart.com/Support/Guides.aspx

Have you had the vehicle checked for DTC'S - diagnostic trouble codes ?.

It sounds like the fuel pressure check valve on the fuel pump has gone bad and your losing fuel pressure when engine is turned off. Try priming the fuel pressure twice, that's when you turn the ignition keys to the run position with out starting the engine for 10 seconds and then turning the key's to the off position and on again for 5 seconds. After the second prim the engine should start, to check this you can lone out a fuel pressure gauge and check the fuel pressure at the shredder valve. You should have 62 to 65 PSI during prim and once the engine is running, it should drop by 5 psi. As for your the accuracy on reading the right amount of fuel in your gas tank, the sensor is apart of the fuel pump sending unit and the float may have gotten bent and nothing you can do to fix it unless you take the fuel pump out again and replace the sending unit. Good luck and keep me posted.

Sound like a reversal of wires on the autostart. Should only cut out if you don't have the key in ignition and apply brake. Did you have this installed or was it in when you bought the vehicle?

I would have the computer scanned ( no SERVICE LIGHTS right ? ) looking for an errant coolant sensor not telling the computer to give your vehicle a bit RICHER ( a little bit more fuel ), since it does start. Just has POOR cold drive away. Hope this helps

Just from what you said it sounds like your vehicle might not be holding its residual pressure which means after you turn a vehicle off, your fuel injection system should hold a certain amount of pressure in the system, but if that pressure drops to fast your vehicle may have a hard time starting. Things to look for when you lose fuel pressure is the fuel pressure regulator may be leaking, fuel pump check valve,leaky fuel injector or they maybe a small leak in one of the fuel lines. I only suggested this cause i had a car with the similar problem.

replace the motor it is burned up