This usually happens when it has been in a snow storm or I washed the truck with a pressure washer. It is an intermittant problem that goes away within an hr to as long as two days but always goes away. It has been happening since i bought the truck. I am the original owner - I have 165,000 miles on it now.
SOURCE: CHEVY SILVERADO 2500HD DURAMAX DIESEL
DTC P1093
Fuel Rail Pressure Low During Power Enrichment
The engine control module (ECM) uses the fuel rail pressure (FRP) sensor to
determine fuel pressure to the fuel injectors. This is then compared to the calculated
target fuel pressure as determined by the ECM. The ECM adjusts the FRP by modulating
the duty cycle of the control driver of the fuel pressure regulator. Injector pulse
duration is determined by the measured rail pressure and the target injection fuel
into each cylinder. If a sensor circuit malfunction is detected, or the commanded
fuel injection pump flow is not within the proper range for a given engine load and
speed, DTCs will be set.
DTC U1000 and U1255
Circuit Description Modules connected to the class 2 serial data circuit monitor for serial
data communications during normal vehicle operation. Operating information and
commands are exchanged among the modules. When a module receives a message for
a critical operating parameter, the module records the identification number of
the module which sent the message for State of Health monitoring. A critical
operating parameter is one which, when not received, requires that the module
use a default value for that parameter. When a module does not associate an identification
number with at least one critical parameter within about five seconds of beginning
serial data communication, DTC U1000 or U1255 is set. When more than one
critical parameter does not have an identification number associated with it, the
DTC will only be reported once. The class 2 serial data line on this vehicle
is a ring/star configuration. The following modules communicate on the class 2
serial data line:
•
The body control module (BCM)
•
The digital radio reciever
•
The driver door module (DDM)
•
The electronic brake control module (EBCM)
•
The front passenger door module (FPDM)
•
The HVAC control module
•
The inflatable restraint sensing and diagnostic module (SDM)
•
The instrument panel cluster (IPC)
•
The memory seat module (MSM)
•
The powertrain control module (PCM)
•
The radio
•
The radio amplifier
•
The rear seat audio (RSA) controller
•
The rear seat entertainment (RSE) assembly w/U42
•
The rear wheel steering control module
•
The remote playback device-CD player w/U1S
•
The transfer case shift control module
•
The transmission control module (TCM) w/Allison transmission
•
The theft deterrent control module
•
The vehicle communication interface module (VCIM) w/UE1
SOURCE: changed oil pressure switch,still no oil pressure
The fuel pump on that model runs through the oil pressure switch so that if the truck looses oil pressure,It kills power to the fuel pump to prevent engine damage.you need to find the cause of the low oil pressure reading(possibly a bad oil switch).That would be the cheapest place to start,or have it checked with a mechanical gauge.Good luck,
ChevRev
SOURCE: 2005 Chevrolet Silverado 2500HD 4x4 Oil Change Reset
Not positive 05 is the same but on my 02 you turn the key to the on position and pump the gas pedal 4 times.
SOURCE: 2001, Duramax Deisel 6.6 won't "restart"
fuel pump is obviouslynot working !
check it & its wiring!!!!!
SOURCE: Need to know Oil Capacity for Duramax 6.6 in 2004
Hello,
The requirement is 10 QTS. I use 10 and check it cause some times they hold 11 QTS. I hope this helps. If you have more questions reguarding this or other conserns please ask me. Please remember high ratings are very important to me.
Thank You,
Roy
Testimonial: "Thanks very much for that Regards Bryan McRae New Zealand"
62 views
Usually answered in minutes!
×