How do i adjust the bi-xenon in my 2009 volvo c70

SOURCE: 2003 volvo s60, how do i adjust headlights

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

SOURCE: HEADLIGHT ADJUST ON AUTOMOBILE

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

SOURCE: volvo c70 2006 hard top door out of alignment how

the bolts on the brackets control the movement of the doorif you leave the top bolts tight,and adjust the bottom,it changes the alignment at the bottom of the door and vice versa

SOURCE: How do I replace the bi-xenon bulb in my 2007

I just did this on my 2008 C70, which I believe uses the same type of bulb. It's very easy. By the time you do your second one, you can probably do it in less than 5 minuites.

1) Take careful note of the orientation of the headlight houseing retaining pin, HID transformer, and bulb retention device.
2) Refer to the owners manual to pull the headlight housing retaining pin.
3) Pull the headlight housing forward until you can access the wiring harness plug. Push the clip on the top of the plug to unlock, then remove the plug.
4) At this poing the entire headlight housing is detached from the car. Take it indoors and have a beer before the next step.
5) Push back the two spring clips and remove the access door from the back of the headlight housing.
6) At this point in the owners manual, the instructions tell you to refer the problem to an expert and do not provide further details. Shoot you got the darn thing out. And you have a beer in hand. You look like an expert. Let's continue.....
7) The low beam light has a transforer attached to the back of the bulb. Unplug the wires attached to the transformer.
7) Twist the transformer counter clockwise 1/8 turn, and remove the transformer.
8) The base of the bulb is now visiable, but the bulb is held in by a large retaining knurled plastic knob about 1-3/4 inch in diameter. Twiist that knob 1/8 inch turn counter clockwise and remove.
9) The old bulb is now free, and can be removed. Do not touch the glass on the new bulb, but carefully seat it in the same orientation in the housing.
10) Assembly is a reverse of the previous steps. Hopefully you paid attention to the orientation during removal, as the bulb, retaining knob, transformer, and housing retaining pin all are keyed and will fit in one way only.
11) Have another beer, and bask in the admiration of your family and friends, you expert you! Congratulations!

SOURCE: 2002 C70 Volvo high beam

There is no way to adjust the beam of light a headlight projects. The bulb filament is designed to project either low beam or high beam. More than likely the filament is burning out. If these are new bulbs, then the glass was probably touched and this causes the bulb to become damaged. If these are new bulbs, you should check to see that the high beams are indeed high beams and low beams were not accidentally installed in their place. If you require additional help on this matter, do not hesitate to ask.