The process of removing car door panels is essentially the same for each make of car. You may need to remove these panels when your fixing locks or power windows, replacing window cranks, installing speakers or replacing the side mirrors. Learning how to remove the panels yourself can save money on simple car repairs. Check out how the door panels are attached to the car. Most panels use screws and bolts but others have snap-in fittings. Gather all the tools you need for removing the door panels. If the panel is attached with screws and bolts, you need a screwdriver or ratchet and socket. Car door panels with snap-in fittings are easily removed with a flathead screwdriver. Locate where the screws and bolts are before starting. These are usually found in the arm rest area, along the bottom or sometimes near the door lights. Roll down the car door window. Begin removing all screws and bolts that hold the door panel onto the car. If your car has snap-in fittings, pry gently on the bottom corner of the door panel until the fittings pop out. Remove the power window control panel if your car has power windows. The control panel should pry out easily, and then you unplug the wiring harness from the back and place it to the side. Use an L pick and flashlight when locating a manual window crank. Look behind the window crank and slide the pick under the edge of the metal clip that holds the crank in place. Remove the clip and pull the crank off. Remove the door handle by unscrewing the small screw located in the center. Gently pull the door handle out until you see the back of the handle and unclip the rod from the door handle. This should remove the handle unless the handle and door lock are attached, then you just unclip the rod from the lock and remove them both together. Unscrew the cap off rear upper corner door panel locks. These don't have a rod attaching them to the handle and unscrew separately from the door handle. Pop the door panel off after you've removed everything. Gently pry on the bottom edge of the door panel until it releases. Pull out and up to completely remove the door panel.
Related Searches:
SOURCE: How to remove door handle on 99 oldsmobile aurora
unscrew the 2 screws on the bottom of the inside panel,
then unscrew the large phillips head right behind the interior handle and remove the plastic cover
next, you need something stiff and wide and flat, like a large meal file with a t-shirt wrapped around it so it doesnt **** up the leather
pry it UP and a little bit outward and it will pop off, I was going on the fly and broke the little brackets and I had to us 1minute gasket to seal them back on really well.
the connectors come off by the little clips on the side, stick a flathead along he side of the connectors and they will click out, you will feel them slip loose.
not the panel should come free from the coor.
next you need to remove the flat metal cover that has 2 bolts in it, basically right in the middle with the right side bolt touching the lock mechanism as well. it will unbolt then slide the tabs down and out...easy.
the door handle is held on by 2 bolts, youll have to squeeze your hands to the right of the metal slider for the window and over the metal bars for the lock. I got the left one with a wrench and the right one I had to stick my left hand where I mentioned and m right hand had the wrench.
the handle will be free by then, and you can slide the left side out first. then gently pull the bottom of the handle housing out and to the left at the same time and it will pop out.
un-screw the two bolts to remove the bars from the lock on the bottom and the top elbow comes off as one piece with the metal bar going downward.
and there you go buddy...I just had to fix my door handle and it reuied removing it, just did it today. took about 2 hours, but I had no idea what was doing and had to figure out the mechanism by myself...computer broke conveniently enough!
SOURCE: How do I replace the
If you slide the door lock slider to the unlock position you can grab a hold of the end of it and pull towards you it's only held on by a clip embedded in the plastic. Once that's removed remove the trim panel behind it to gain access to the door handle assy.. The handle is riveted on to the door skin so you will have to drill out the rivet after that the handle will slide towards the front of the car about 1/2 inch and its free just disconnect the lock rod and install your new handle it sounds like a lot but is actually very easy
355 views
Usually answered in minutes!
remove exterior trim on passenger rear door
handle won't work from inside?
×