Removing interior trim and headliner in 1995 Toyota Camry

If your motor is audible and your fuses and connectors are okay, you may have to take a close look at the plastic gear parts up in the roof. The nylon parts do wear out since they are in the roof and more exposed to different temperatures. If any of that mechanism fails then your sunroof will stop working even if the motor is still good. It is a bit of a PITA to get to it since you will have to remove the headliner to get at the mechanism and then identify the worn part and replace it CAUTION: The sunroof system is timed from the factory so that the motor shuts off automatically when the sunroof window reaches a certain position. Extreme care must be taken when removing the motor, timing may be thrown off causing possible damage to the sunroof system. Anytime the motor is removed from the sunroof assembly the sunroof glass panel must be in the FULLY CLOSED POSITION or the unit will be out of timing. The drive motor cannot be reset to the park position after being removed.
CAUTION: The sunroof motor should only be powered through the vehicle battery and sunroof wire harness. Applying power to the sunroof motor leads will cause failure of the control module.
Move glass panel to the fully closed position.
Move glass panel to the fully closed position.
Remove the A-pillar trim. (Refer to 23 - BODY/INTERIOR/A-PILLAR TRIM - REMOVAL)
Remove the B-pillar upper trim. (Refer to 23 - BODY/INTERIOR/B-PILLAR UPPER TRIM - REMOVAL)
Remove the C-pillar trim. (Refer to 23 - BODY/INTERIOR/C-PILLAR TRIM - REMOVAL)
Remove the D-pillar trim. (Refer to 23 - BODY/INTERIOR/D-PILLAR TRIM - REMOVAL)
Remove the sunvisors. (Refer to 23 - BODY/INTERIOR/SUN VISOR - REMOVAL)
Remove the overhead console. (Refer to 8 - ELECTRICAL/OVERHEAD CONSOLE - REMOVAL)
Disconnect the control switch wire connector.
Remove headliner as necessary to gain access to sunroof drive motor. Refer to Headliner Removal and Installation for proper procedures.
Disconnect the drive motor wire harness connectors (Sunroof Drive Motor and Express Module).
Remove drive motor fasteners and remove motor from the sunroof housing

They go down inside front A pillar an inside rear D pillar . To get at them you need to take trim off an the headliner down .
Sunroof Housing Rear Drain Hose Replacement (Impala)
Remove the headliner. Refer to Headlining Trim Panel Replacement in Interior Trim. Remove the rear quarter lower trim panel. Refer to Rear Quarter Lower Trim Panel Replacement in Interior Trim. Disconnect the rear sunroof drain hose from the sunroof module rear spigot. Remove the tape from the rear sunroof drain hose tube.
Disconnect the rear sunroof drain hose from the rear sunroof drain hose tube. Remove the rear sunroof drain hose tube from the upper retainer clip. Remove the rear sunroof drain hose from the rear pillar
The front is simalier .

Important: This sunroof system is timed from the factory in order to allow the actuator to shut off automatically when the sunroof window reaches a certain position. Use extreme care when removing the actuator from the sunroof module. This may cause the timing to be thrown off. This may damage to the sunroof. Anytime the actuator needs to be removed from the module, ensure that the sunroof window is in the fully closed position.
Remove the sunroof window. Refer to Sunroof Glass Panel Replacement .
Slide the sunshade fully rearward. Move the sunroof window to the vent position. Remove the sunroof screws (two on each side). Remove the sunroof window from the module.
Place the sunroof module in the fully closed position. Remove the headliner. Refer to Headlining Trim Panel Replacement in Interior trim.
Tools Required ?€¢
J 38778 Door Trim Pad and Garnish Clip Remover

?€¢
J 2772-C Headliner Installer

1. Remove the sunshades. Refer to Sunshade Replacement .
2. Remove the overhead console, if equipped. Refer to Roof Console Replacement .
3. Remove the sunshade retainers. Refer to Sunshade Anchor Replacement .
4. Remove the power sunroof switch, if equipped. Refer to Sunroof Switch Replacement in Roof.
5. Remove the sunroof trim lace, if equipped. Refer to Sunroof Seal/Molding Replacement in Roof.
6. Remove the dome light, if equipped.
7. Remove the coat hooks. Refer to Coat Hook Replacement .
8. Remove the assist handles. Assist Strap Replacement
9. Remove the rail lamp. Refer to Roof Side Rail Lamp Replacement in Lighting.
10. Remove the windshield side garnish molding. Refer to Windshield Pillar Garnish Molding Replacement .
11. Remove the upper quarter trim panels. Refer to Rear Quarter Upper Trim Panel Replacement .
12. Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement .
13. Pull down on the door opening weatherstrip seal on both the front and the rear doors.
14. Remove the 2 rear retainers (2) using J 38778 Door Trim Pad and Garnish Clip Remover. Disconnect the headliner electric harness at the right side of the rear window shelf. Rotate the right front seatback to a horizontal position. Remove the headliner from the vehicle through the right front door.
    

Disconnect the electrical connector from the actuator.
Important: Before removing the actuator, ensure that the pins J 41718 are tight and holding the cable.
Thread the J 41718 into the front sunroof window screw hole in order to retain the cable adjustment. Remove the sunroof actuator screws. Remove the sunroof actuator from the module. Did you look for a video on youtube ?

you need to replace glass or is it leaking if leaking then you have to remove upper seat belt covers pop off remove bolt 14mm and the trims on upper pillars pry off carefully held in by clips remove covers on interior light at front where sunroof switches are there are screws by bulbs disconnect connector remove center light cover and screws disconnect connector with clean hands remove rbber trim around sunroof opening and plastic cover on each side of sunroof glass held on with plastic screw clips then remove four 10mm nuts lift sunroof glass out of car remove cover and screws from rearview mirror all plastic trims around headliner move pass seat forward most and flip back rest all way down roll pass window fully down then slide headliner out of car now you can remove electrical connectors and remove water flow hoses from sunroof unit remove 8 12mm nuts holding frame to roof remove through door you will see the track sunroof slides on remove nuts along problem is silicone between track and frame is deteriorated lift track clean replace silicone reattach frame to roof dont put trims or liner in till test connect switches and glass to frame make sure sunroof works and closes fully then go through car wash to see if leak is fixed

Check for any obstruction in the rail.

Also, can check this procedure to test your components...
Power Sunroof - REMOVAL & INSTALLATION (click over pic for zoom)

Motor
See Figure 1

1. Remove the sunroof switch panel by pushing it to the side and disengaging the pawl, then pulling it downward.

Fig. 1: The sunroof switch panel is retained by a metal clip

1. Remove the sunroof switch bracket.
2. Unplug the sunroof motor wiring harness connectors.
3. Remove the sunroof motor mounting screws.
   

Disassembly of the sunroof motor is not recommended.

To install:

1. Lightly lubricate the drive gear with grease and install the sunroof motor to the sunroof assembly.
2. Plug in the electrical harness connectors to the sunroof motor.
3. Operate the sunroof to verify proper operation.
4. Install the sunroof switch bracket and the sunroof switch panel.
   

Sunroof
See Figures 2 and 3



Fig. 2: Exploded view of the sunroof assembly on 1993-94 vehicles



Fig. 3: Exploded view of the sunroof assembly on 1995-97 vehicles-1998 models similar

1. Tilt up the sunroof lid.
2. Remove the lid side trim.
3. Remove the lid bolts and the lid assembly.
4. Remove the rear drain mount screws and the drain.
5. Remove the shade assembly holders from the sunroof frame.
6. Remove the shade assembly.
7. Remove the sunroof switch, interior accessories and headliner.
8. Remove the switch bracket.
9. Remove the motor assembly, spacer and clip.
10. Remove the wind deflector mount holders from the sunroof frame.
11. Remove the wind deflector.
12. Disconnect the drain hose.
13. Remove the sunroof brackets.
14. Remove the sunroof frame assembly.
15. Remove the link and wire assemblies.
    

To install:

1. Tilt up the sunroof lid.
2. Install the link and wire assemblies.
3. Install the sunroof frame assembly.
4. Install the sunroof brackets.
5. Connect the drain hose.
6. Install the wind deflector.
7. Install the wind deflector mount holders on the sunroof frame.
8. Install the motor assembly, spacer and clip.
9. Install the switch bracket.
10. Install the sunroof switch, interior accessories and headliner.
11. Install the shade assembly.
12. Install the shade assembly holders on the sunroof frame.
13. Install the rear drain mount screws and the drain.
14. Install the lid bolts and the lid assembly.
15. Install the lid side trim.

Hope helps (remember rated this help).

There is a drain hose that runns down the frt windshield pillar. the garnish should pop off and follow the hose. removing the headliner is a little more difficult. to see the hose connection to the sunroof housing.

The bigest problem with this model jeep sunroof is the cable conduit in the rear of sunroof is broken loose. can be accesed by removing the headliner. But the tracks are accessed from the sunroof opening after removing the glass. the part department at the dealership can give you a breakdown basicly the only replacable parts are the tracks, Price about $200.00 each.

You have to remove the interior trim panels to allow you to pull down the corners of the headliner. Once you can see the sunroof track you will be able to see where the drains attach and hook them back up.