Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on Jan 08, 2012

Euroclean ecb 2000 is overheating. Then it won't work

Had plug replaced 2months ago. Used it again stop working, but motor was very hot

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Jan 14, 2009

SOURCE: 2000 Jetta Heater Not working

2000 jetta warms up when idling, but gets cold as soon as I start driving.

Ad

Jonah Oneal

  • 14092 Answers
  • Posted on May 29, 2009

SOURCE: replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?

fix the radiator first.because coolant temperature sensor need to be in antifreeze.when antifreeze get up to 190 degrees. the coolant sensor act as a thermostat.it resistance decrease then the pcm will command cooling fans to run.if antifreeze low the coolant temperature sensor not going to work. engine is going to over heat.

Anonymous

  • 6982 Answers
  • Posted on Jul 20, 2009

SOURCE: Air Conditioner blower motor resistor was replaced

Motor is also energized by a relay. check that and also check that the motor itself is good by running a hot lead right to it. I'm sure you already checked the fuse and know the switch is good?

Ron Hatcher

  • 94 Answers
  • Posted on Jun 02, 2011

SOURCE: 2000 Volkswagon Beetle won't start

you have probly blown the headgasket sorry to say.

Randy Ohler

  • 14585 Answers
  • Posted on Sep 04, 2011

SOURCE: Air won't blow cold and

Couple of things come to mind. You have climate control, so it could be that the temperature sensor is bad or the plenum door actuator is bad. I would lean more to the sensor, as the door usually is open or closed when it goes bad. This would leave you with cold or hot all the time. Also the climate control console could be bad. You can have this checked with a hand held computer.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
1answer

2000 olds alero cranks then makes a metal grinding sound and won't start

You need to have your flywheel: replaced.Your starter motor engages against the fly wheel at the back of the motor. Every time your motor stops it tends to be in the same few positions (just the way things work) so there is more stress on some parts of your fly wheel than others. Because of this the teeth wear out on the fly wheel which means the starter can correctly engage on the fly wheel which is the grinding noise.
0helpful
1answer

2000 Buick Regal windshield wipers stopped working during hard rain.

Make sure wiper arms are tight they are on a spline also where the wiper arm transmissin conects to the wiper motor therw is a nut that holds a z shaped bracket that losens up and oblongs the rectangular slot so the wipers stop with the least resistance.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/craig_a14a43e01fd0835a

0helpful
1answer

1991 Honda Accord got hot. Now it won't start. It

car overheated can cause failure at the head gasket.Overheated till the car just stops can cause ring failure thus no compression and worped head.car will not run in some cases.
1helpful
2answers

My heater just stopped working, it still blows air but just not hot air, i checked the coolant and its fine, it had never over heated. so please help

check to be sure that the thermostat is closing, sounds like yours is stuck open, which happens a lot ,, if the water won't stay in the motor long enough to heat,, then you won't get any hot air coming out , follow the top radiator hose to the motor, under that housing is where you will find the thermostat , thay are pretty cheap, less than 10 bucks normally ,, I'd just replace it
1helpful
1answer

My blower motor started making a ton of noise. And everything stopped. I tested the motor, it worked but shaft was bad, and it really dragged. I replaced the motor. However, it still won't come on. I...

Follow the blower wires back to the resistor, which is screwed into the heater box. Remove the resistor and check for heat damage and continuity. Most likely it is burned up. The assembly also contains a relay, which is usually only used for high speed. The assembly is $32 at autozone.See pic below.
jturcotte_525.jpg
0helpful
1answer

Hi, I have a 2000 chrysler 300M with overheating problems. Few months ago replace the water pump, radiator and a hose. I just replace the thermostat and temp sensor. A year ago replace fans. But still...

theres a bleeder crew in the front of the motor by the thermose stat the you have to open when the car is running so the cooling system can release the air from the motor. it worked for me. 10mm socket will fit it.
0helpful
1answer

2001 sportage kia--- just got motor job 2months ago...ac has stopped working...and rpm gauge doesnt work and is pulling hard....Is there a fuse that could have blowed and needs replacing? retta smith

The speedometer and rpm gauges are operated by sensors instead of cables on your model. It is very possible that either your sensors are not hooked up to your tranny or that they are in need of replacing. Check all fuses.
1helpful
1answer

I replaced the blower motor resistor to fix the

Did you inspect the connector on the harness side and resister side.. They can overheat and melt,
Not finding what you are looking for?

30 views

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29492 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...