License plate bulb replacement

According to a post on Traverse Forum, the issue might not be with the bulbs themselves, but rather with the connectors that slide onto the bulb. These connectors may be corroded, which could prevent the bulbs from working . Another possibility is that the lens the bulb attaches to may be full of dirt, especially if you live in a dusty area .

If neither of these solutions work, it's possible that there is a problem with the fuse for the license plate lights. The license plate lamps are powered by the 10 amp left parking light circuit fuse located in the under hood fuse panel. If any of your parking lamps on the left side are out, this could be the problem. If those lights are working, then the fuse should be good. The fuse is easy to get to, so it's worth pulling it out and reseating it or replacing it .
Fuse box location and diagrams: Chevrolet Tahoe (2007-2014) - YouTube

That sounds like a blown fuse, but your vehicle also has 'lighting modules'.

2003-2011 Lincoln Town Car Fuse Box Diagram

https://knigaproavto.ru > shemy > 607-2003-2011-linc...
Jul. 22, 2018 - Fuse Box Diagram Lincoln Town Car S, D, E, C, U (2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011)


..

License Plate Lamp Removal and Installation

1. If necessary, remove the license plate.

1. Remove the pin-type retainers and the luggage compartment lid trim panel.

1. Disconnect the license plate lamp electrical connector.

1. Remove the lamp socket from the license plate lamp.

1. Using a suitable tool, through the access hole, release the clips and remove the license plate lamp.

can you rich from trunk,maybe has clips.

raise trunk lid look on the inside behind your license plate light there should be access to the bulb there. You will see the wires going in to the bulb there will either be a flt plate that can be removed to access bulb or where the wires enter there will be a round socket that you can twist counter clockwise and remove the bulb socket for bulb replacement. hope this helps.

here is the instructions on how to replace license plate bulbs.

Remove the 2 screws that retain the license lamp lens to the liftgate.

Remove the license lamp lens from the liftgate.

Remove the bulb (1) from the socket.

Remove license plate. Unscrew the screws on the underside of the bumper. Slide the lights back toward the trunk and then down through the opening. Unscrew bulb and replace with a new one.

Reverse steps to reinstall the lights.

Check this reference guide...

2002 Hyundai Accent Car Lightbulb Size Guide
Low Beam Headlight Bulb Size: 9003/HB2
High Beam Headlamp Light Bulb Size: 9003/HB2
Parking Light Bulb Size: 2357A
Front Turn Signal Light Bulb Size: 2357A
Rear Turn Signal Light Bulb Size: 1156
Tail Light Bulb Size: 1157
Stop Light Bulb Size: 1157
High Mount Stop Light Bulb Size: 921
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 1156
Front Side Marker Light Bulb Size: 2357A
Rear Sidemarker Light Bulb Size: 168
Map Light Bulb Size: DE3175
Dome Light Bulb Size: DE3175
Step/Courtesy Light Bulb Size: DE3022
Trunk/Cargo Area Light Bulb Size: DE3022

From Sylvania Lamp Replacement Guide
License plate
168
168LL Long Life Upgrade: Up to twice the life of the standard lamp.


I hope help you with this. Good luck (remember rated this help).

License Plate Lights Removal & Installation License plate lamp retainer clips

To Remove:
Remove or disconnect the following:

1. License plate
2. Pin-type retainers and the luggage compartment lid trim panel
3. License plate lamp electrical connector
4. Lamp socket from the license plate lamp
5. Using a suitable tool, through the access hole, release the clips and remove the license plate lamp

To Install:

1. Install or connect the following:
2. License plate lamp
3. Lamp socket to the license plate lamp
4. Electrical connector
5. Luggage compartment lid trim panel
6. License plate