Question about 1995 Saturn Sc

Open Question

How do you adjust the clutch on my 95 saturn sc1

Is there a way to adjust the clutch

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 17 Answers

SOURCE: Clutch adjustment 95 Jeep YJ

no, there is no clutch adjustment. the clutch is hydraulic, and self adjusting, there are several things that can go wrong with these. with normal wear the fluid can run low allowing air into the system, causing a weak peddle. they can also develop leaks in the master and slave cylinders resulting in fluid loss also causing a weak peddle leading to an inopperative clutch. check the fluid level in the clucth master cylinder(next to the brake master cylinder. if it is empty, refill it(it takes brake fluid) then cycle the clutch peddle a few times and check for leaks. if there is air trapped in the line the clutch will need to be bled. there is a bleeder screw on top of the slave cylinder, bleed it just like bleeding brakes.

Posted on May 28, 2009

Ad
  • 8 Answers

SOURCE: 95 v.w. jetta 3 4 cyl. clutch adjustment ????

there is no adjustment. may have failed hydaulic master or slave cylinder. also I would try bleeding 1st they may have opened system when they did clutch.

Posted on Mar 23, 2009

  • 186 Answers

SOURCE: bleed the clutch

No way to bleed the clutch system.You need to buy a clutch master/Slave assy from saturn.Comes completely full of fluid & ready to install.It has retainers to hold slave pin in place until fully installed.Once installed you push the pedal & you will hear a faint click which is the slave retainer breakaways relieving.No other way to bleed although aftermarket parts house will sell you individual pieces.hope this helps

Posted on May 21, 2009

  • 4793 Answers

SOURCE: 1997 Saturn SC1 with manual transmission, slipping

you can check if its the clutch by puting car in 4th gear and releasing clutch pedal slowly if the pedal travels a long way out and the engine just spins then its the clutch.

Posted on Mar 21, 2010

Testimonial: "This worked perfectly! Clutch is BAD"

  • 201 Answers

SOURCE: What size/power are my 95 Saturn SC1 rear speakers?

Well you can look at your car manual or look on the speakers for how much wattage it uses. If not go to a mechanic and ask for help. Hope this helps!?

Please rate solution - Thanks.

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch adjustment 95 saturn


As most later models like the mid eighty's their is no manual adjustment the clutch assembly is usually worn outJohnny

Mar 16, 2012 | 1995 Saturn Sc

1 Answer

How to bleed the clutch on a 2001 saturn sc1


very hard to get to, shops sell them as pre-bled master and slave unit.

Oct 21, 2010 | 2005 Saturn SC1

1 Answer

How do you change a clutch cable on 97 saturn sc1?


Impossible as it has a hydraulic clutch, and no it cannot be adjusted. It has a small master cylinder and a slave cylinder, just like a brake system. If one of those has failed, you buy a pre-bled replacement for the whole little system and bolt it in.

Aug 30, 2010 | 1997 Saturn SC

1 Answer

1998 Saturn SC1 manuel stick is hard to shift into 1st & 2nd gear


Try to double clutch the clutch pedal. How to double clutch; push the clutch in moving the stick to neutral, then release the clutch and then push it back in and shift into first or second gear. If it works then it is not the shift linkage and could be a clutch adjustment. First how far do you have to release the clutch pedal until the clutch plate starts to engage? If only an inch or so the clutch pedal needs to be adjusted, which is an easy fix (this is more common). The other possible problems could be the clutch plate, throwout bearing of syncros could be bad. If it is one of the previous problems double clutching should buy you some time.

Jul 01, 2010 | 1998 Saturn SC

1 Answer

How do i get the slave cylinder out of the trans on a 95 saturn sc1


Unbolt the the two nuts that hold it onto the transmission. Then grab the slave cylinder and turn it counter clockwise and it should pop out. That is correct because holding it in the hole and turning it clockwise seats it back into the transmission.

Remember to remove the connection between the clutch pedal and the master cylinder or put a brick or something to hold the clutch pedal up or else removing the slave cylinder without the above note will ruin the hydraulics and allow air to get into this airless system.

Feb 26, 2010 | 1995 Saturn Sc

2 Answers

Will a 95 saturn 1.9 manual transmission bolt to a 98 saturn 1.9 automatic transmission?


This is the automotive equivalent of a ***-change operation. In short, dont do it...
The problem you have is not if the tranny will fit (which it won't as a direct bolt-in replacement), the problem is in everything else that needs to be moded. Your engines computer is not programed to recognize or work with a manual tranny. You would need to modify the console to accept a manual shifter, install a clutch and clutch pedal assembly, plumb the needed fluid systems, and replace the entire wiring harness in the engine bay. In short, if you are asking - this won't go well and even if it did work, the car would not be reliable. By the time you spend everything involved in this project, it would be much cheaper to buy a 95 or 98 Saturn with the transmission that you prefer.

Sep 23, 2009 | 1998 Saturn SL

1 Answer

2001 saturn sc1 grinds when going into third gear


sounds like you got a bad shift syncro for 3rd gear, its inside the trans,cuse ive never adjust shift cables on a s-series now matter what was done to the trans,and that cable controls more than just 3rd gear so its gotta be the syncro,,sorry,,,cheaper to get a used trans than to fix

Jul 30, 2009 | 2001 Saturn SC

1 Answer

I have a 95 Saturn SC1


disconnect battery jack up car and put it on stands. starter is on the back side of the engine disconnect the wires from the starter and remove the bolts that hold it to the trans perform the steps in reverse order to intsall. let me know if you need any more help.

Jun 09, 2009 | 1993 Saturn SC1

1 Answer

95 saturn sc1 all of a sudden had engine light on and the idle just went way low, also effects how tranny shifts, but will barely stay running in gear with brake on. Sometimes it starts idling fine and...


You either have a bad engine coolant temp sensor & connector.Located under upper radiator hose at cylinder head Yellow & black wire.Original sensor is ceramic & replacement will be brass from saturn.Also you may check for vacuum leaks at PCV hose & valve.Hope this helps

May 15, 2009 | 1993 Saturn SC1

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...