Trying to locate fuel pump housing - 1991 Honda Accord

The fuel pump drive module is typically located in the central junction box, which is located under the driver's side of the dashboard. To access the fuel pump drive module, you will need to remove the panel covering the central junction box.
Here is a general guide for finding the fuel pump drive module in a 2003 Navigator:

1. Locate the central junction box: The central junction box is usually located under the driver's side of the dashboard, near the steering column.
2. Remove the panel: The panel covering the central junction box is usually held in place with a few screws. Use a screwdriver to remove the screws and carefully lift off the panel.
3. Locate the fuel pump drive module: The fuel pump drive module will be a small electrical component with a series of wires connected to it. It may be labeled as the "fuel pump relay" or something similar.

If you are having trouble finding the fuel pump drive module, you may want to consult your owner's manual or a repair manual for specific instructions. Alternatively, you can try searching online for a diagram or video that shows the location of the fuel pump drive module in a 2003 Navigator.

You may need a fuel line tool that compresses a spring in the collar. You can get them at any auto store..

FUEL PUMP RELAY 1987 Nissan/Datsun Truck D21 Truck 2WD 2.4L FI 4cyl The Fuel Pump Relay is located: Under hood, passenger side, front engine area, rear of headlight housing, mounted on upper fenderwell

The fuel pump is located in the tank.........Remove the tank and tap the sending unit and pump housing which u will see the lines attached to around to the unlock possition and remove......Be careful not to damage the gasket..Hope this helps.

It is built onto the fuel pump. You can access the fuel pump in the trunk under the carpet. Remove the bolts from the rectangular cover and it is the black sensor pushed into the fuel pump housing.

You should try the Fuel Shut off Switch or AKA-(INERCIA Switch)

The inertia fuel shutoff switch is located in the luggage compartment on the door hinge support above the left hand inner wheel house.

The location is clearly marked on the vehicle.

The fuel pressure regulator is located in the fuel rail, held in by a torx screw.

Release pressure from the system by cranking the car with the fuel pump fuse out, or byt depressing the relief valve on the end of the fuel rail.
Unbolt the regulator/housing assembly, unhook the vacuum hose, and remove the regulator/housing assembly.

Installation is reverse order.

If you need to replace the regulator that is located in the fuel pump, it is not serviceable. Luckily they rarely fail.

did you check the fuel pump fuse and relay,if ok then fuel pump.fuel pump is located inside the tank,good luck let me know..

the pump is in the tank

Removal

1. Relieve the Fuel System Pressure . Refer to the procedure in this section.
   

Cushion Cover and Pad, Rear Seat — One-Piece and 50/50 Split Fold Removal

1. Remove the two rear seat cushion bolts.
   

1. Fold the rear seat back cover and cushion (60084) forward.
   

1. Carefully pull the rear seat cushion and cover (60030) out from under the rear seat back cover and cushion and remove the rear seat cushion and cover from the vehicle
   

1. Remove the rear seat cushion and cover (60030). Refer to Section 01-10 for the removal procedure.
   

1. Remove the three luggage compartment floor cover hold-down pins and fold the luggage compartment floor cover (45455) forward until the fuel pump assembly access plate is visible.
   

1. Remove the four fuel pump assembly access plate screws, the ground lead, and the fuel pump assembly access plate from the chassis.
   
   
   
   
   

1. Disconnect the fuel pump assembly electrical connector.
   
   
   
   
   

1. On 4-door vehicles, remove the fuel vapor tube shutoff valve bolt and the evaporative emission tube shut off valve (9G332) from the bracket on the fuel pump assembly housing.
   
   
   
   
   

1. Loosen the two hose clamps and disconnect the two fuel pump hoses from the fuel pump hose fittings on the fuel pump assembly housing.
   
   
   
   
   

1. Remove the four screws (2-door) or eight screws (4-door) and lift the fuel pump assembly housing from the fuel tank (9002).
   
   
   
   
   

1. Disconnect the fuel level sensor electrical connector.
   

1. Remove the two fuel level sensor washers and fuel level sensor nuts and the fuel level sensor.
   
   

-------------------------------------------------------------------------------------
Section 10-01: Fuel Tank, Filters, Lines and Electric Fuel Pump 1996 Aspire Workshop Manual
REMOVAL AND INSTALLATION Fuel Pump Removal

1. Remove the fuel level sensor. Refer to the Fuel Level Sensor removal procedure in this section.
   

1. Remove the fuel pump screw, fuel pump grommet and the fuel pump bracket from the bottom of the fuel pump (9350).
   
   
   
   
   

1. Remove the fuel tank sender filter bracket, fuel tank sender filter (9A011) and the fuel tank sender filter retainer from the fuel pump.
   

1. Disconnect the fuel pump electrical connector.
   

1. Remove the clamp and the fuel pump from the fuel pump assembly housing.