Cruise Control - 1996 Buick Lesabre

step 1
Remove the left sound insulator
step 2
the stop switch is here, way way up top
use flash light to see it.
it is there.
top of pedal it is there. SM books step1.

buy the service manual.?
if the switch ever sticks on , cruise ENDS
it is a NO, switch normally open contarts
no calibration is stated so its PnP

Which engine ?
Cruise Control Description and Operation (3.6L)
Cruise Control Description and Operation (3.4L)

Do you know what all is involved in C.C. operation ?


Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions at speeds above 40km/h (25 mph). However, steep grades may cause variations in the selected speeds. The main components of the cruise control system are:
• The cruise control module assembly
• The cruise control switches
• The cruise control release switch
• The powertrain control module (PCM)
• The stoplamp switch assembly
• The vehicle speed sensor


The cruise control module controls the operation of the cruise control system. The cruise control module monitors the signal circuits of the cruise control switches. When the normally open cruise On/Off switch closes with a switch activation, the cruise control modules detects a high voltage on the signal circuit. The cruise control module activates the cruise control system.The set/coast switch and the resume/accel switch will not operate the system when the cruise control module has not activated the system based on the cruise control on/off switch signal circuit .
The cruise control module monitors the cruise control set/coast switch in order to determine when to capture and maintain the vehicle speed. The cruise control module monitors the vehicle speed signal circuit in order to determine the desired speed. The PCM pulses the vehicle speed signal circuit at 4000 pulses per minute. After an initial set speed has been established, the cruise control module also uses the cruise control set/coast switch signal circuit in order to tap down the set speed when the cruise control module detects a switch activation.
The cruise control module monitors the cruise control resume/accel switch signal circuit in order to determine when to resume the previous set speed. This feature only works within the same ignition cycle and as long as the cruise wasn't turned off using the cruise control On/Off switch since the last cruise engagement. After the set speed has been resumed, the cruise control module also uses the cruise control resume/accel switch signal circuit in order to tap up the set speed when the cruise control module detects a switch activation.
The cruise control module assembly has a controller and an electric stepper motor to vary the throttle in each different cruise control mode. Two components in the module assembly help to do this. The electronic controller and the electric stepper motor. The controller monitors vehicle speed and operates the stepper motor. The stepper motor operates in response to the controller, to maintain the desired cruise speed. The electric stepper motor moves a strap that is attached to the cruise control cable which moves the throttle

Check the wire connector that plugs into the cruise control under the hood. Sounds like a loose connection. Remove the and reinsert the wire connector several times to make a better connection. Stepping on the brake pedal disengages the cruise control by a switch on the brake pedal, not the computer.

It is HVAC 1fuse #39 in the rear fuse block ,this powers the on/off switch for cruise control ! Fuse Block - Rear Beneath the left rear seat. What engine does it have ? 4.2 L or 5.3 l There is no vacuum involved in the operation of the cruise control ! Your vehicle has electronic throttle control .
Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions at vehicle speeds above 40 km/h (25 mph). Steep grades may cause variations in the selected vehicle speeds.
The following are the main components of the Cruise Control System:
?€¢
The powertrain control module (PCM)

?€¢
The On/Off switch

?€¢
The Resume/Accel switch

?€¢
The Set/Coast switch

?€¢
The TCC brake switch

?€¢
The stop lamp switch

?€¢
The throttle actuator control (TAC) motor

?€¢
The vehicle speed sensor

Cruise Control Engaged
The cruise control system will engage and adjust the vehicle speed based on the activation of the following cruise control switches:
?€¢
On/Off

?€¢
Resume/Accel.

?€¢
Set/Coast

The cruise control switches are located on the multifunction/turn signal lever.
The powertrain control module (PCM) monitors the signal circuits of the cruise control switches in order to determine when to capture and maintain the selected vehicle speed. The PCM uses the throttle actuator control (TAC) module motor in order to control the vehicle speed. For further information on the TAC System, refer to Throttle Actuator Control (TAC) System Description in Engine Controls - 4.2 L.
Ignition positive voltage is supplied from the 10 ampere HVAC 1 fuse to the cruise control switch via the ignition 3 voltage circuit. When the normally open cruise control On/Off switch is turned On, the switch closes and the PCM detects a high signal voltage on the cruise control on switch signal circuit. When the normally open Set/Coast switch is pressed, the switch closes and the PCM detects a high signal voltage on the cruise control set/coast switch signal circuit. To engage the cruise control system, turn the On/Off switch On and momentarily press the Set/Coast switch. The PCM will confirm that the cruise control enable criteria has been achieved. The PCM will engage the cruise control system and record the selected vehicle speed. The PCM sends a class 2 message to the instrument panel cluster in order to illuminate the cruise control indicator. Pressing the accelerator pedal, while the cruise control system is engaged, will allow the driver to override the cruise control system in order to accelerate the vehicle beyond the current set vehicle speed. When the accelerator pedal is released, the vehicle will decelerate and resume the current set vehicle speed. The driver can also override the current set vehicle speed via the Set/Coast switch and the Resume/Accel switch. When the cruise control system is engaged, pressing and holding the Set/Coast switch will allow the vehicle to decelerate from the current set vehicle speed without deactivating the cruise control system. When the Set/Coast switch is released, the PCM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the cruise control system is engaged, momentarily pressing the Set/Coast switch will allow the vehicle to decelerate at 1.6 km/h (1 mph) increments for each time that the Set/Coast is momentarily pressed, with a minimum vehicle speed of 37 km/h (23 mph). When the normally open Resume/Accel switch is activated, the switch closes and the PCM detects a high signal voltage on the cruise control resume/accel switch signal circuit. Activating and holding the Resume/Accel switch, when the cruise control system is engaged, will allow the vehicle to accelerate to a greater vehicle speed than the current set vehicle speed. When the Resume/Accel switch is released, the PCM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the cruise control system is engaged, momentarily activating the Resume/Accel switch will allow the vehicle to accelerate at 1.6 km/h (1 mph) increments for each time that the Resume/Accel switch is momentarily activated, with the maximum acceleration total of 16 km/h (10 mph) over the current set vehicle speed . Momentarily activating the Resume/Accel switch, after the cruise control system has been disengaged by pressing the brake pedal, will recall the previous set vehicle speed that is recorded in the PCM.

Bummer deal! This may be a way to tell you some tail lights are burnt out. Some cruise controls have a fuse in a second location.
The fuse is not in right or is blown. Check with a new fuse. Hope this helps. ...gc http://www.auto-tune-up-and-repair-options.com/

We had the same problem and ended up replacing the switch. We used a small flat-tip screwdriver and lifted along the edge of the switch. With the switch removed from the steering wheel, we disconnected the wire connector and installed the new switch by reversing the order.

You may have a bad cruise module

no not a fuse may be the switch itself this is common and parts are not badly priced. replace the switch. It just pops out. The directions will tell you to take out the airbag first but it will sneek out of there.

Check vacuum tee under hood by fire wall. Looks like a fishing cork, three ports.