These are the codes i got p0030, p0053,p0302,p0053, p0054,p0134

These codes refer to 3 different issues.
P0053 - HO2S Heater resistance Bank 1, sensor 1.
P0054 - HO2S Heater Resistance Bank 1 Sensor 2
P0324 - Knock Sensor (KS) Module Performance.
P0326 - Knock Sensor Circuit Excessive Spark Retard.
P0597 - Thermostat Heater Control Circuit Open.

You need to get a good mechanic to look at this. The HO2S codes refer to both of the 'O2' sensors in the exhaust, (mounted before and after the Catalytic Converter). They monitor the exhaust gas mixture to correct fuel mixture to the engine to control exhaust gas pollution levels. If one is detecting a wrong reading, the fuel/air mix is automatically adjust.
The Knock sensors detect vibration from when the fuel is burning. If the sensor detects a 'bang' when it shouldn't be there it alerts the ECM (cars brain) to adjust the timing sequence.
Wrong readings cause the ECU to adjust the fuel/air mixture to the wrong setting causing rough engine running.
The thermostat code is for the wiring to the coolant thermostat sensor.

No code tells you to replace a part , need to do diagnostic's for said code .
P0141 - O2 Heater Circuit (Bank 1, Sensor 2) Description: See the description for DTC P0135. Possible Causes: See the possible causes for DTC P0135. Diagnostic Aids: See the diagnostic aids for DTC P0135. Application Key On Engine Off Key On Engine Running Continuous Memory All GO to Pinpoint Test DW .
DW: Heated Oxygen Sensor (HO2S) DW: Introduction DW1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS) Are DTCs P0040, P0041, P0053, P0054, P0055, P0059, P0060, P0132, P0133, P0135, P0138, P0139, P0141, P0144, P0147, P0152, P0153, P0155, P0158, P0159, P0161, or P1127 present?
Yes No For DTCs P0040 or P0041, GO to DW2 .

For DTCs P0053, P0054, P0055, P0059 or P0060, GO to DW14 .

For DTCs P0132, P0138, P0144, P0152 or P0158, GO to DW20 .

For DTCs P0133 or P0153, GO to DW3 .

For DTCs P0135, P0139, P0141, P0147, P0155, P0159 or P0161, GO to DW9 .

For DTC P1127, GO to DW19 . For all others, GO to Section 4, Diagnostic Trouble Code (DTC) Charts and Descriptions .
DW9 DTCS P0135, P0139, P0141, P0147, P0155, P0159 OR P0161: CHECK FOR A SOURCE OF POTENTIAL HO2S CONTAMINATION

• Investigate the following items as potential sources of HO2S contamination:
  • use of unapproved silicon sealers
  • fuel contaminated by silicon additives
  • excessive oil consumption
  • glycol leaking internally in the engine
  • lead-contaminated fuel
  • short drive cycles in cold weather
  • use of unapproved cleaning agents

Is a concern present?
Yes No REPAIR the source of the contamination.

CHANGE the engine oil and oil filter.

RESET the keep alive memory (KAM). REFER to Section 2, Resetting The Keep Alive Memory (KAM) .

REPEAT the self-test. GO to DW10 .

DTC P0014: Exhaust Camshaft Position (CMP) System Performance

What is the trouble code or are you just throwing parts at it to see how much money you can waste?

https://www.engine-light-help.com/chevy-check-engine-light
.html

This should help

P0134 - O2 Sensor Circuit No Activity Detected Sensor 1 Bank 1
P0135 - O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1
P0053 - O2 Heater Resistance Bank 1 Sensor 1
P0030 - O2 Heater Control Circuit Bank 1 Sensor 1
You need to replace the O2 Sensor Bank 1 Sensor 1
Carquest can help you get the correct part and help you locate it.

theres more then one o2 sensor the code its throwing tells you which ones bad the code you have is for bank one

There is a fault with the inbuilt heater in the oxygen sensor, before the catalytic converter, on the exhaust pipe the same side of the engine as cylinder 1. The oxygen sensor has four wires within the cable sheath to the top of it. Two of the wires will share the same color. These wires supply power to an internal heating element wire within the sensor. Follow the cable from the oxygen sensor to the connector, you can do a lot testing here. Check the resistance between the two 'same coloured ' wires. The resistance is low, somewhere between 1 and 10 ohms. If there is no continuity (infinite resistance) then this is the fault and the sensor needs to be replaced. The codes: P0030 the oxygen sensor heater relay is at fault P0053 Oxygen heater resistance error P0135 Sensor 1 bank 1 error You are looking at replacement. A further confirmation take the connection from sensor 1 bank 1 and swap it with the sensor 1 bank 2 on the other side of the engine. The codes should 'transfer' and show P0036; P0059 and P0141.

May be errant codes from losing power, erase them and see if they come back - [ I'm betting they won't.]

P0016 - Crankshaft Position Camshaft Position Correlation Bank 1 Sensor A
P0030 - Heated Oxygen Sensor (H02S) Heater Control Circuit Bank 1 Sensor 1
P0031 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 1 Sensor 1
P0032 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 1 Sensor 1
P0036 - Heated Oxygen Sensor (HO2S) Heater Control Circuit Bank 1 Sensor 2
P0037 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 1 Sensor 2
P0038 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 1 Sensor 2
P0050 - Heated Oxygen Sensor (HO2S) Heater Circuit Bank 2 Sensor 1
P0051 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 2 Sensor 1
P0052 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 2 Sensor 1
P0053 - HO2S Heater Resistance Bank 1 Sensor 1 (PCM)
P0054 - HO2S Heater Resistance Bank 1 Sensor 2 (PCM)
P0056 - Heated Oxygen Sensor (HO2S) Heater Circuit Bank 2 Sensor 2
P0057 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 2 Sensor 2
P0058 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 2 Sensor 2
P0068 - Throttle Body Airflow Performance (PCM)
P0100 - MAF Sensor Circuit Insufficient Activity