Need spark plug firing order for 1997 hyundai sonata

check your crank shaft sensor behind the harmonic balincer

The firing order diagram you requested is below. Best of luck and thank you for using Fixya!
Greg

1996 Hyundai Sonata 2.0L Firing Order



Firing Order: 1-3-4-2

Please clarify your question. Do you need to know the spark pug gap, or the firing order, or something else. I would like to help you, but I need more information.

My online Sonata manual shows these possibilities, but does not identify which applies specifically to 2000 Sonata.
Also, when you talk to the dealership parts counter, you'll need to know whether your 2000 Sonata is (a) 4-cylinder 2.4L MFI DOHC engine, or (b) 6-cylinder 2.5L MFI DOHC engine.
Its easy to tell - just count your spark plug wires.

-- begine excerpt from 2000 Hyundai Sonata Repair guide --

The crankshaft position sensor is located next to the flywheel.
The crankshaft position sensor is located next to the flywheel/torque converter.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The crankshaft position sensor is located on the driver-s side of the vehicle, down by the lower radiator hose.
The crankshaft position sensor is located on the engine near the crankshaft pulley.
The crankshaft position sensor is located at the front of the engine near the timing belt.

--- end excerpt from 2000 Hyundai Sonata repai guide ---

For the 1997 Hyundai Sonata 2.0L DOHC In-Line 4-Cylinder:

Firing Order:
1 - 3 - 4 - 2
Cylinders:
..........(back)..........
|...4....3....2....1...|
.........(front)
Coil Connections:
(back)
|..1..|
|..4..|
|..3..|
|..2..|
(front)

Let me know if this helped and THANKS for using FixYa.com!

For the 2005 Hyundai Sonata
I do not know if you have the 2.4L In-Line 4-Cylinder or 2.7L V6; however I have included both below....

For the 2.4L In-Line 4-Cylinder:
Firing Order:
1-3-4-2
Cylinders:
..........(back).........
|...1....2....3....4...|
.........(front)

For the 2.7L V6:
Firing Order:
1-2-3-4-5-6
Cylinders:
.......(back)........
|...1....3....5...|
.......................
|...2....4....6...|
.......(front)
Coil Connections:
(back)
...3
...6
...2
...5
...4
...1
(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

For the 3.0L:

Firing Order:
1-2-3-4-5-6

Cylinders:
....(back)
6.....4.....2
5.....3.....1
.....(front)

Distibutor Connections:
....(back)
4.....5.....6
o.....o.....o
||||||||||||||||||||
o.....o.....o
3.....2.....1
....(front)

Let me know if this helped or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Autozone.com says that for this vehicle the firing order is 1-2-3-4-5-6 and the set-up is 2/1 4/3 6/5 meaning that the #6 cylinder is far right on the back. It goes #1 #3 and #5 in the front and #2 #4 and #6 in the back.

hi there, you need to make sure all wires to spark plugs are tight and very snug, you will also need to check the distributer cap to make sure no burns are on it, and make sure the plugs are in proper firing positions, the spark rotation might be out of sequence.....also make sure spark plugs are clean of all oil, and dirt, firing pin in distributer cap might be bad.....hope this helps....shia