2006 Sienna battery went dead. After charging, navigation and radio don't work. Screen works and says "NO MAP DVD - Insert Disc" Checked Radio fuses 1,2 and 3 are good, as well as 12v outlets.

Are you 100% sure the disc is the correct one for this car's GPS?

Hello, I hope this helps. If no change then you probably have a hardware/ wiring issue and the dvd player may need to come out. Please advise
1. Confirm the DVD RSE system is inoperative. (blank screen) 2. For vehicles with Toyota navigation system: Perform the following procedure to turn OFF the RSE Lock function. A. Press the INFO switch on the navigation unit. B. Press the "Screen Setting" touch button on the navigation display. C. Under the "Rear Lock" option, press the "OFF" touch button and then press "OK" in the upper right part of the display. D. Press the DVD switch on the RSE system (if a DVD is NOT already in the player, insert one) and confirm screen is ON and the system will play DVDs. 3. For vehicles without Toyota navigation system: Perform the following procedure to turn OFF the RSE Lock function. A. Push the Audio Control knob multiple times to cycle through the various options (Bass, Mid, Treble, etc.) until "REAR LOCK" is shown on the screen. B. Turn the Audio Control knob so the display says "OFF" next to "REAR LOCK". C. Press the DVD switch on the RSE (if a DVD is NOT already in the player, insert one) and confirm screen is ON and the system will play DVDs. 4. If the above procedure resolves the concern, explain the system operation to the customer.This procedure is described in the Audio/Video" section of the vehicle Owner's Manual. 5. If the above procedure does NOT resolve the concern, perform RSE diagnosis using the Technical Information System (TIS), 2006 model year applicable vehicle Repair Manual.

The dealer can help, w/vin #

Engine room Junction Box - on left side of Engine Compartment (Drivers side in USA) - Fuse RAD 1 (20A), Fuse RAD 3 (30A) - there is another fuse that goes to your ECU, it works with the radio, but you won't need to pull it. In case you do - it is Fuse ECU-B (10A)

Press station 1 and 6 and turn the ignition key to on position but donot start the vehicle, you will see the unlock code flashing, note the number that is your radio code, read your vehicle manual and insert code to unlock.

This SIB may apply to this issue:

SI B 65 24 07
Audio, Navigation, Monitors, Alarms, SRS August 2007
Technical Service

SUBJECT
CCC Navigation Map DVD not Detected


MODEL
E90, E91, E92, E93 (3 Series) with SA 609 (CCC Navigation)

E60, E61 (5 Series) with SA 609 (CCC Navigation)

E63, E64 (6 Series)

E70 (X5) with SA 609 (CCC Navigation)

Vehicles produced from 8/31/2006


SITUATION
When entering into the navigation system, the screen only displays "Please insert DVD", even though a DVD map is inserted in the drive.

CAUSE

Incorrect map DVD

CCC software or hardware error

PROCEDURE
On a customer complaint basis proceed as follows:

Always verify that the correct map DVD is used (identified by DVD-CCC). Try a known good map DVD and see if the problem is resolved.

Update the complete vehicle per SI B09 05 01 (Programming and Coding with Progman) Procedure B, using Progman 25.00.00 or higher.

If the fault is still present, replace the DVD drive. Refer to Repair Instructions RA 65 83 580

PARTS INFORMATION
Part Number
Description
Quantity

Refer to EPC
DVD drive
1

WARRANTY INFORMATION
Covered under the terms of the BMW New Vehicle Limited Warranty.

Please refer to the latest KSD for all applicable labor operations and allowances.

If the appropriate labor operation is not contained in KSD, then a work time labor operation should be used.

go too your dealer and ask for a new disc. that should fix your problem.

check the fuses

I shipped my 2006 Yukon Denali from USA to Saudi Arabia. When I to purchase the Middle East map DVD for the navigation system. GM Navigation answered me that they do not have the middle east DVD and I should contact the European branch. The dealer in Saudi Arabia is asking for $1200 for the disc and I know it is worth no more than $400. Could you please direct me to someone who sells the 06 Denali navigation map DVD? Thanks..

Installing the DVD Map Disc Your dealer/retailer may have installed the map DVD. If the map DVD was not installed, do the following to load it:
Read the following steps completely.

1. Turn the ignition on. The vehicle must be in P (Park) to perform this operation.
2. Press (power) to turn the navigation system on.
3. Press the NAV hard key.
4. Touch the Insert Map Disc screen button. The screen opens to access the map DVD slot.
5. Load the map DVD partway into the slot. The system pulls it in. The screen cannot be closed until a double beep is heard.
   Notice: Pressing directly on the navigation screen may cause damage. Repairs would not be covered by the vehicle's warranty. Do not press directly on the navigation screen.
   
6. To close the screen, slightly push up on the two outer corners until the screen is in position. Then push the screen in by pushing on the four outer corners until a click is heard.
7. Set the search area. See "Setting the Search Area" earlier in this section.

Ejecting the DVD Map Disc The navigation portion of the system cannot be used if the DVD map disc is not loaded.

1. Press the MENU key to enter the Menu options, then press the MENU key repeatedly until Nav is selected or touch the Nav screen button.
2. Touch the Map Database Information screen button.
3. Touch the Eject Map Disc screen button. The screen tilts, exposing the map DVD slot.
4. Press the eject button, located next to the DVD map disc slot, and the disc ejects. Pull the disc out. The screen cannot be closed until a double beep is heard.
   Notice: Pressing directly on the navigation screen may cause damage. Repairs would not be covered by the vehicle's warranty. Do not press directly on the navigation screen.
   
5. To close the screen, slightly push up on the two outer corners until the screen is in position. Then push the screen in by pushing on the four outer corners until a click is heard.