Question about Volkswagen Beetle

1 Answer

73 super bettle, turn singles light up but don't

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Volkswagen Master
  • 17,970 Answers

The Flasher is located:
- Hazard flasher: Front seating area, driver side, under dash, above kick panel, mounted on firewall
- Turn signal: Front seating area, driver side, under dash, above kick panel, mounted on firewall

Hope helps.

Posted on Sep 15, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 tacoma flashers don't work but turn sig do work!


The hazard switch gets power from the horn fuse which is hot all the time, and from the turn signal fuse which is hot when the key switch is on. The turn signal switch gets power from the hazard switch and both use the same flasher.
So if the turn signals work but the hazard switch does not power the lights, and both fuses have power, I would say the problem is inside the hazard switch.

Feb 19, 2013 | Cars & Trucks

1 Answer

How do i fix my blinkers on my 1971 f100 ford ?


There is a flasher unit for the turn signals, separate from the hazard flasher, that is under the dash. If the fuse for the turns is good, and you already know the bulbs are good since the hazards work, then you may have a bad turn signal switch.
When you use the turn switch, do the bulbs come on and stay on, or nothing? If they come on and don't blink, then it's probably a bad turn flasher unit. If they don't come on at all, suspect a bad turn signal switch. But first check the fuses, then pull off the connector to the turn switch and see if you have one hot wire there, with key on. That one hot wire will be from the fuse.

Mar 01, 2012 | Cars & Trucks

1 Answer

Turn signals on my 1992 Park Avenue blinked slower and now donot work at all. My emergency flashers work fine and all blink but I have no turn signals and nothing lights up when signal is left or righ


About your 1992 Buick Park Avenue 3.8L SFI OHV 6cyl. the Flasher is located:
Hazard flasher: Front seating area, driver side, under dash, mounted above kick panel

Turn signal: Front seating area, driver side, under dash, driver side of steering column, mounted on support bracket

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 11, 2011 | 1992 Buick Park Avenue

3 Answers

I have a 1995 chevy cavalier and the turn signals just stay on and don't blink. I have changed the flasher and the multi function switch and still no luck


First, is it doing it on BOTH isdes or just on one side? Example: turn signnals flash OK when turning left, but only come on and stay on when turning right. If it is doing this, then you most likely have either a blown bulb or a bad bulb socket on the side that is not flashing. You need to check both the FRONT and REAR bulbs to make sure they are all functioning properly.
If it is doing it on BOTH sides, then you either have a bad flasher, or at least 2 bulbs burned out (one or more on each side).

Are you sure you replaced the correct flasher? The flasher for the HAZZARD lights is plugged into the convinience center under the left side of the dash. If this is the flasher you replaced, it is the wrong one.
The turn signal flasher is mounted to the driver's knee bolster bar near the steering column. It is held to the bar with a clip. (see diagram)

9_25_2011_3_20_38_pm.gif

Sep 25, 2011 | 1995 Chevrolet Cavalier

1 Answer

The turn signal lights on my 2004 Ford Explorer stay on and don't blink. My hazards flash, but there is no clicking sound of normal use. Eventually, they tend to come back on, or blink with the...


Sounds like your flasher relay is broken. A lot of people think that because their hazard flashers work that everything is OK, this isn't so. Hazard flashers are on a seperate system, and as such they have their own relay.
You will need to find where your indicator relay is located and replace it with the correct type.

Aug 17, 2011 | 2004 Ford Explorer

1 Answer

I don't know where the signal light flasher is located the signal lights don't flash


Your vehicle has 2 flasher relays. One for the turn signals and one for the hazard lights. The turn signal flasher relay is located on the drivers side, under the dash, mounted on the drivers (Left) side of the steering column. The hazard flasher is mounted on top of the steering column. Do not get them mixed up.

Aug 12, 2011 | 1991 Chevrolet Corsica

1 Answer

No turn signals they come on but don't flash


It's probably the turn signal flasher. It is usually located under the dash along with the hazard light flasher. If you don't know what it looks like, then go to a parts store and look at a new one. Once you have located one, then remove it. Try the hazard flashers. If they work, then replace that flasher with a new one. If they don't, then reinstall that flasher and look for another one like it. When you find one, replace it with the new flasher and try the turn signals. (remember : the key must be on for the turn signals to operate). I hope this information helps you and thank you for using Fixya.com.

Jun 28, 2011 | Chevrolet TrailBlazer Cars & Trucks

3 Answers

Turn signals dont work on 1993 skylark. all bulbs are good. hazard lights blink fine. turnsignal dash light stays green and doesnt blink


There are 2 separate flasher relays. 1 for the turn signals and one for the hazards. I believe you have a bad flasher relay for the turn signals. The location of that is in the front seating area on the drivers side, under the dash on the drivers side of the steering column, mounted on support bracket. I provided a picture of what it should kind of look like although the picture I gave you is an aftermarket one so the color and such may be a little different but will look the same. Don't get it mixed up with the hazard relay which is located in the front seating area on the drivers side under the dash above the kick pane lmounted on top of the convenience. I am almost 100 percent sure the flasher and hazard relay are the same so if you want to just swap them out in order to have turn signals that should work. You won't have hazards however. I hope this helps you and good luck.


clifford224_215.jpg

May 07, 2011 | 1993 Buick Skylark

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...