Changing battery on a 2004 bmw 325ci

ck here.........

https://www.bimmerfest.com/threads/replaced-battery-now-lost-instrument-cluster.571529/

Question edited for clarity. MAKE!
Question moved to Category.

https://www.google.com/search?q=bmw+325ci+vs+bmw+325i

325i

Fuse Box Diagram BMW 3-Series (E46; 1998-2006)

https://fuse-box.info > bmw > bmw-3-series-e46-1998-...
Here you will find fuse box diagrams of BMW 3-Series 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005 and 2006 (316i, 318i, 318d, 320i, 320d, 323i, 325i, 328i, ..

Ci, Cabriolet

1998-2006 BMW 3 (E46) Fuse Box Diagram

https://www.e46fanatics.com > ... > E46 > E46 General
Oct 29, 2018 - Mine still has the card that identifies all the fuses but that is a good reference if yours is missing. 2002 BMW 325Ci Cabriolet Automatic, 140K ...

..

remove the expansion tank and have a look at the seams those tanks have a habit of distorting and start leaking

I'm confused. You are asking about camshaft position for a BMW 325ci in a question posted under 2000 Mitzubishi Endevor and didn't mention WHAT ABOUT camshaft position....???

The battery for your car is located in the trunk. There are jumper terminals located under the hood in the front of your car. There is a Red (+) terminal that is under a little black cover on the passenger side of the engine bay near the firewall. Right near that is a silver/gray bolt that is bolted to the frame of the car. This is the negative terminal.

Make sure both cars are and all accessories are off:
1) Connect the Postive cable to the dead battery
2) Connect the Positive cable to the good (BMW) terminal
3) Connect the Negative cable to the good (BMW) terminal
4) Connect the Negative cable to the dead battery
5) Start the BMW. (if you have 2 people then gently rev the engine)
6) Start the dead car.
7) Let both cars idle for a while before disconnecting any cables
8) Remove in the opposite order.

Removal & Installation

1. Disconnect the negative battery cable.
   
2. Disconnect the throttle position (TP) sensor electrical connector.
   
3. Remove the screws and the TP sensor.
   

Throttle position (TP) sensor electrical connector



TP sensor


To install:

1. Install the screws and the TP sensor. Tighten screws to 7 inch lbs. (3 Nm)
   
2. Connect the throttle position (TP) sensor electrical connector.
   
3. Connect the battery ground cable.
   

http://forums.bimmerforums.com/forum/showthread.php?t=1209580 If you need to replace the intake
This link will guide you thru step by step with pix... it took me approx. an hour to replace!! Good luck!!!!
[email protected]

is there anything extra i need to know on changing the battery on my 2005 645ci bmw

disconnect the negative battery. remove the belt by rotate the tensioner roller clockwise. from the left car side u will see three hexagon screw 13mm under the altenator. loose out the screw and remove the altenator. before that unplug the two wire behind the altenator.tq

Fuses & RelaysThe fuse box is located under the engine hood on the left side, near the upper strut housing or near the battery.
Various relays are also mounted on the fuse box for easy accessibility.



Flashers
The flashers are located behind the bottom center of the lower instrument trim panel.



Review the...
- BMW E36 Fuse Box Relay Layout
- 325ci Owners Manual

Hope helped.