The dashborad says suspension fault - LR3 Land Rover Cars & Trucks

That could work , You mite be able to test the sensor in question with ohm meter . Test the front one an see what the resistance is ,then check the back one. I don't know what it should be with out looking it up in the service info . You could also check to see if the sensor is getting power from the control module , an see if there is a return input to the module .
There are a few DTC'S this able to set !
Air Suspension Control Module Diagnostic Trouble Code (DTC) Index
Air Suspension Control Module Diagnostic Trouble Code (DTC) Index DTCs Description Source Action B1318 Battery Voltage Low Air Suspension Control Module Go To Pinpoint Test C . B1342 Air Suspension Control Module Air Suspension Control Module INSTALL a new air suspension control module. REFER to Module-Air Suspension Control . SET the front ride height. REFER to Air Suspension Initialization (Clear DTC B2140). CLEAR the DTCs. REPEAT the self-test. B1485 Brake Pedal Input Circuit Battery Short Air Suspension Control Module RERUN On-Demand Self-Test. MAKE SURE that the brake pedal is not pressed. If DTC is returned again, REPAIR brake pedal position (BPP) circuitry. B1566 Door Ajar Circuit Short to Ground Air Suspension Control Module Go To Pinpoint Test D . B2140 Initialization Failure (Vehicle Ride Height Not Programmed) Air Suspension Control Module REFER to Air Suspension Initialization (Clear DTC B2140). C1439 Vehicle Acceleration EEC-V Circuit Failure Air Suspension Control Module Go To Pinpoint Test E . C1724 Air Suspension Height Sensor Power Circuit Failure Air Suspension Control Module Go To Pinpoint Test F . C1726 Air Suspension Pneumatic Failure Air Suspension Control Module Go To Pinpoint Test G . C1760 Air Suspension Height Sensor High Signal Circuit Failure Air Suspension Control Module Go To Pinpoint Test H . C1770 Air Suspension Vent Solenoid Output Circuit Failure Air Suspension Control Module Go To Pinpoint Test I . C1790 Air Suspension LR Air Spring Solenoid Output Circuit Failure Air Suspension Control Module Go To Pinpoint Test J . C1795 Air Suspension RR Air Spring Solenoid Output Circuit Failure Air Suspension Control Module Go To Pinpoint Test K . C1830 Air Suspension Compressor Relay Circuit Failure Air Suspension Control Module Go To Pinpoint Test L . C1917 Steering Electronic Variable Orifice (EEVO) Out-of-Range Fault Air Suspension Control Module Go To Pinpoint Test Q .

• Uneven vehicle height

• Circuitry.
• Rear pneumatic fault.
• Air compressor assembly.
• Air suspension control module.

• Go To Pinpoint Test I .

You need to check with dealer to remove fault code for suspension thru 5052 scanner. The system is sending a fault and it eventually ends up in the ECM

I’m happy to assist further over the phone at https://www.6ya.com/expert/howard_977676954994c5b2

If the suspension is "hanging" on any wheel there is a sensor that detects it. Also if a shock absorber is not maintaining pressure it will show a suspension fault...Check it out!

This can be due to few reasons which can be checked.
1. Fault in the wheel bearings , is there is a play on the wheel bearing/hub the wheels can wobble.
2. Fault in the alignment or fault in wearing of the brake pads.
3. fault in setting of the calipers.
4. Fault in the suspension system, check the strut mountings, shock absorbers and suspension links.

Problems with the air suspension seem to be less frequent with the Sport than in previous Range Rover models, but they still do occur. One owner reports "Whenever my RRS is lowered to "access" level a suspension system fault message apprears.". Another reports " Had the RRS back less than 2 hours and another "suspension fault." Also kept receiving messages that the vehicle is raising slowly and vehicle will raise when system cools. Couldn't even drive because it wouldn't raise out of access mode. Anyway, back to the dealer. Picked the RRS up again today-dealer said the EAS compressor was faulty and replaced it. So far everything is ok." Overall, most of the problems seem to be related to bad suspension height sensors or bad compressors. Angus Wade of the Czech Republic had his suspension light come on when in Germany; it started yellow and then red, then disappeared when he stopped and restarted the engine -- and has not happened since. His dealer said they have seen this a bit.

Weak Compressor: An official Technical Service Bulletin (TSB) LS-204-004 addresses "ELECTRONIC AIR SUSPENSION (EAS) WARNING MESSAGE AND LAMP ILLUMINATION". This deals with the warning message "Suspension Fault - Normal Height Only" message appearing with the Air Suspension Warning Lamp on. Computer diagnosis shows pressure increasing too slowly or unable to pressurize, with no air leaks. The usual problem is the compressor exhaust valve sticking, causing an internal air leak when the compressor is active. The bulletin recommends renewing the air compressor (RQG500090 is the latest specification air compressor with a stronger exhaust valve return spring)and installing and updating the air suspension control module software using WDS disc 13 or later.

Suspension Fault Message (random): One owner reported getting random suspension fault messages on his brand new RR Sport purchased in June 2006, well after the fix was in for the weak compressor. His suspension Fault message and Suspension Warning Light (Amber) came on after 5 days of ownership. He stopped and restarted the car, which caused the light and message to disappear, but they came on again after 5 minutes. Later the same day, the warnings disappeared again.

I have heard that on 2006 models, EAS fault messages can be caused by an internal leak in the Air Suspension compressor exhaust valve. The fix is said to be replacing the compressor updating the software.

Hope helps.

Hi,
You have a problem with one of the following: 1. The wiring circuit for the air suspension warning system has a fault. 2. Your air suspension air pressure is not being maintained so you may have a fault there.
Have a diagnostic check done and this will pin point the problem.
Hope this helped.

Need to get the vehicle scanned for fault codes.
The most common issue is the air pump/compressor for the electronic air suspension.
Relatively easy to replace, but you still need to get the vehicle scanned for fault codes. Once the fault has been repaired, again you will need to get the faults cleared.
No really a DIY repair im afraid.

you can try turning the ignition on and off , only to position two ond off with out starting , between 20 - 30 times this sometimes confuses modules and causes them to clear faults , if not i would recomend getting it plugged in , if vehicle is not in warranty go to landrover specialist , much cheaper!!!!!