Question about Mitsubishi Montero Sport

1 Answer

How to replace rear brakediscs shogunsport - Montero Sport Mitsubishi Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 5,370 Answers

The caliper, pads needs to be removed, front one is bolted by screws, but rear disc brakes are bolted by pins.The pins needs to be removed.If the pins are rusted and hard to take out,then wd-40 spray or any other good rust lubricating spray has to be used.-------- For complete detail, with step by step diagrams.Click the link below:--- http://howtobyme.blogspot.com/2011/09/how-to-replace-rear-brake-discs-on.html ----------- This will help.Thanks.Helpmech.

Posted on Sep 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the factory amp on 09 hhr ls


Preliminary Procedures
Remove the rear seat. Refer to Rear Seat Replacement.
Remove the left quarter lower trim panel. Refer to Quarter Lower Rear Trim Panel Replacement.


Preliminary Procedure
Remove the rear compartment floor stowage compartment tray. Refer to Rear Floor Trim Plate Replacement.
1
Rear Seat Nut (Qty: 6)
Caution: Refer to Fastener Caution in the Preface section.
Tip
Roll the seat forward enough to get access to the nut that attaches the center seat belt assembly to the floor.
Tighten
45 N·m (33 lb ft)
2
Rear Seat Bolt (Qty: 3)
Tip
• Adjust the seat forward or rearward to access the bolts.
• Remove the plastic trim pieces to gain access to the nuts.
Tighten
45 N·m (33 lb ft)
3
Rear Seat Assembly

Preliminary Procedures
Remove the quarter upper trim finish panel. Refer to Quarter Upper Trim Panel Replacement.
Remove the rear compartment trim panel. Refer to Rear Compartment Trim Panel Replacement.
Remove the floor trim plate. Refer to Rear Floor Trim Plate Replacement.
1
Quarter Lower Trim Finish Retainer (Qty: 2)
2
Quarter Lower Trim Finish Panel Assembly
Caution: Refer to Fastener Caution in the Preface section.
Procedure
Remove the cargo tie down loop anchor plates and bolts.
Remove the rear passenger seat belt guide.
Disconnect the rear passenger seat belt so that the trim panel can be removed around the seat belt. Refer to Rear Seat Belt Replacement.
Pull the trim panel toward the inside of the vehicle to disengage the retainers.
Tighten
9 N·m (80 lb in)
3
Quarter Lower Trim Finish Panel Retainer (Qty: 5)

Sep 11, 2018 | Cars & Trucks

1 Answer

Do I have to change my license plate assembly since my bulb is out on my 2004 Cadillac cts 3.6l v6


no just change the bulb .

Open the rear compartment.
Remove the rear compartment lid applique. Refer to Rear Compartment Lid Applique Replacement in Body Rear End

1.Remove the rear compartment lid trim. Refer to Rear Compartment Lid Inner Panel Trim Replacement .
Remove the fastener securing the rear compartment pull down strap to the rear compartment lid.
Remove the rear compartment pull down stap.
Remove the fastener securing the rear compartment release handle escutcheon.
Remove the rear compartment release handle escutcheon.
Remove the push-in retainers securing the rear compartment lid trim to the rear compartment lid.
Remove the rear compartment lid trim from the compartment lid.

Disconnect the rear compartment lid applique electrical connector (4).
Remove the fasteners that retain the rear compartment lid applique (1) to the rear compartment lid (2).
Remove the rear compartment lid applique (1) from the rear compartment lid (2).
Remove the rear compartment lid applique electrical harness pass through (3) from the rear compartment lid (2).

Remove the license lamp socket from the rear compartment lid applique by turning it counter clockwise.
Remove the license lamp bulb from the socket if replacing.
Remove the license lamp from the rear compartment lid applique by lifting the retaining tabs and sliding the lamp away from the applique.

Jan 20, 2017 | 2004 Cadillac CTS Sedan

1 Answer

Where are drains located on a 2003 chevrolet impala sunroof?


They go down inside front A pillar an inside rear D pillar . To get at them you need to take trim off an the headliner down .
Sunroof Housing Rear Drain Hose Replacement (Impala)
Remove the headliner. Refer to Headlining Trim Panel Replacement in Interior Trim. Remove the rear quarter lower trim panel. Refer to Rear Quarter Lower Trim Panel Replacement in Interior Trim. Disconnect the rear sunroof drain hose from the sunroof module rear spigot. Remove the tape from the rear sunroof drain hose tube.
Disconnect the rear sunroof drain hose from the rear sunroof drain hose tube. Remove the rear sunroof drain hose tube from the upper retainer clip. Remove the rear sunroof drain hose from the rear pillar
The front is simalier .

Dec 22, 2015 | 2003 Chevrolet Impala

1 Answer

How do I replace rear parking sensor


You have to take bumper cover off .
Remove rear bumper fascia. Refer to Rear Bumper Fascia Replacement . Disconnect electrical from the rear object sensor. Lift the locking tabs on the housing and remove the rear object sensor.
Preliminary Procedure
  1. Remove the compartment sill plate. Refer to Rear Compartment Sill Trim Plate Replacement .
  2. Remove rear wheel liners. Refer to Rear Wheelhouse Panel Liner Replacement .
1
Rear Fascia Push Pin Retainers (Qty: 2)
2
Rear Fascia Nuts (Qty: 4)
Tighten
10 N?·m (89 lb in)
3
Rear Fascia Bolts (Qty: 2)
4
Rear Fascia Bolts (Qty: 6)
5
Rear Fascia
Tip
?€¢
Energy absorber and fascia are removed together. Cannot be separate on vehicle.


?€¢
Disconnect the electrical connectors.

Dec 22, 2015 | 2006 Cadillac DTS

1 Answer

2006 Tahoe. Where is the auxiliary blower motor located?


It is located behind the right rear quarter panel , In the back right of the interior !
Remove the right rear quarter trim panel. Refer to Rear Quarter Trim Panel Replacement - Right Side in Interior Trim.
Removal Procedure
  1. Remove the rear seat. Refer to Rear Number 2 Seat Replacement or Rear Number 2 50-50 Seat Replacement in Seats.
  2. Remove the Third Pillar trim panel. Refer to Third Pillar Trim Replacement .
  3. Remove the garnish molding. Refer to Body Rear Corner Garnish Molding Replacement .
  4. Remove the door sill plate. Refer to Liftgate Door Sill Plate Replacement .
  5. Remove the quarter panel trim screws.
A lot involved in this but not to difficult !
  1. Remove the rear door sill trim plate. Refer to Front Side Door Sill Plate Replacement or to Rear Side Door Sill Plate Replacement .
  2. Remove the lower rear seat belt cover and bolt.
  3. Remove the trim panel from the vehicle.
Remove the sill plate. Firmly pull the sill plate up and out from the retainers.
Remove the sill plate from the vehicle. Start from the front of the door sill. Use a flat-bladed tool in order to pry the door sill plate.
Rear Side Door Sill Trim Plate Replacement
Use a flat-bladed tool in order to pry the door sill plate. Remove the sill plate from the vehicle.
Body Rear Corner Garnish Molding Replacement
Remove the rear upper garnish molding. Refer to Rear Upper Garnish Molding Replacement .
Pull down on the upper corners of the garnish molding in order to disengage the retaining clips. Pull in order to disengage the remaining retaining clips. Remove the rear corner garnish molding from the vehicle. Inspect the rear corner garnish molding for broken or missing retaining clips. Replace the retaining clips as needed.
Good Luck ! Fun job !!!!!

Jun 07, 2015 | 2006 Chevrolet Tahoe

1 Answer

Brake system


Remember to bleed longest brake line first and finish with shortest.

The ABS module has some flow valves in it too. May need to have mechanic test pressure going into and coming out of ABS.

Check for Vacuum pressure in Power Brake Booster.

Feb 23, 2014 | Ford Super Duty Cars & Trucks

1 Answer

Replace rear speakers in a 2004 Cavalier


you have to remove the rear deck cover by folding rear seats down and pull plastic push pins out. there are four. once they are out the rear deack will pull off. Once it is off you should be able to see how the speakers come out. just replace them with the new ones and replace the rear deck and pins.

Oct 09, 2009 | 2004 Chevrolet Cavalier

2 Answers

1992 BMW 320i Automatic


Go to pdftown.com. They have a BMW 3 series service manual. Very good manual. I use it all the time.

This is the link for the manual. It is a large file so it will take a while, but it is free. http://pdftown.com/search/node/BMW+3+Series+E36+wiring

Dec 04, 2008 | 1997 BMW M3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...