SOURCE: Volvo 850 1996 4 door sedan Speedometer not working
Mark,
As long as you have the instructions to replace the speeometer drive gear go ahead, and do it.
One BIG question I have for you....how do you know that the mileage is not way over what you've been told?...
small tip for the future.......if you ever look at another car for anybody, and the speedometer doesn't work...pass up the car..there is always another one down the road waiting for you.
Hopefully this will help you, and thanks for letting us at FixYa.com help out...happy New Year
SOURCE: Read a PO410 code,1996 850 GLT volvo, secondary
The most common cause is either a bad air pump (under your battery tray) and/or a bad SAS check valve which is connected in to your exhaust next to the firewall in the engine compartment. It could also be a bad relay for the motor. Less common, but possible, other bad components are the vacuum solenoid that controls the SAS valve, which is located by the radiator or a broken/leaking vacuum line to or from the solenoid.
You can test the motor by jumping the relay or applying 12v straight to it. If the motor runs it most likely is not the problem. If not, it's likely that there is water in it and you should replace both the motor and SAS valve. The SAS valve is a pain to get unbolted, at least on turbo cars. You can check the solenoid by just making sure there is vacuum going to the SAS valve a few seconds after starting up the car cold, and checking the lines for any obvious wear in the rubber elbows or breaks in the plastic line.
SOURCE: 1996 volvo 850 GLT how to replace air valve and pump
VOLVO STARTED USING THIS SYSTEM IN 1996 AND 1997 850 MODELS IT IS AN AIR PUMP --------------SMOG PUMP TO MEET EPA EMISSIONS THE DIAGRAM OF THE SYSTEM IS LOCATED UNDER THE HOOD AND SHOULD TELL YOU WHERE THE VALVE IS LOCATED THERE ARE MANY ECU SYSTEMS USED ON VOLVOS AND THIS SHOULD PUT YOU IN THE RIGHT DIRECTION IF YOU STILL HAVE A PROBLEM GIVE ME THE 2 BIG NUMBERS ON THE ENGINE MANAGEMENT ECU
SOURCE: reset check and service engine lights
It's in the console under the coin holder, in front of the gear shifter. You have to remove the coin holder and you will see it.
SOURCE: 1996 Volvo 850 GLT Fuse #15 keeps blowing out
Hi!
Since you've got a '96 I assume your #15 fuse is 10 amps and for the following components:
Audio System, Courtesy Lights, Door Open Light, Trunk Light, Glove Box Light, Remote Control Central Locking System, Oil Level Sensor, Seat Belt Reminder, Data Link Connector.
Turn ignition to OFF, turn off all interior lighting (by operating the selector inside the car), close all doors, wait about 20 seconds and insert a new fuse. If the fuse is blown immediately upon insertion my guess would be that you have an aftermarket audio system with faulty wiring or maybe something is wrong with you Data Link Connector. If that is not the case the problem might prove a little bit harder to find, and you'll definitely need a wiring diagram. Check this site:
http://www.volvoclub.org.uk/volvo_workshop-850techdocs.shtml
If the fuse is not blown immediately upon insertion: Good, the components affiliated with the fuse can then be grouped by what ignition position they are active at (OFF, 1, 2) and tested individually.
POSITION OFF:
- Door open light, courtesy lights, glove box light, trunk light, remote central locking system.
Make sure the glove box light really is turned off when closing the glove box.
After that it's simply a matter of testing these components one after the other (with the ignition at position OFF) by opening/closing doors, turning on/off trunk light etc, checking the fuse between each component test.
Make sure that the interior lighting is turned off when you test the central locking, or else you might end up faulttracing central locking when the problem was with the interior lighting :)
(Since the interior lights can be set to turn on when the central locking is operated).
POSITION 1:
- Usually the audio system, unless it's an aftermarket system.
If the fuse breaks the second you turn the ignition to position 1 the audio system probably has faulty wiring.
POSITION 2:
If the fuse breaks the second you turn the ignition to position 2 one of these two components is the culprit:
- Seat belt reminder, oil level sensor.
Fasten all seat belts and try again with a new fuse.
If the fuse still breaks the oil level sensor is most likely the culprit.
If the fuse didn't break the seat belt reminder is the culprit. If so you can simply disconnect the seat belt reminder relay, ridding you of both your fuse problem and the annoying seat belt reminder. The relay is located behind the cover over the drivers feet (easily removed, just a couple of torx screws, no breakable interior clips).
The central locking relay and the alarm module are also found there, as well as some other electrical components.
The Data Link Connector is an unlikely culprit, but it's probably best if you unplugged it completely during testing.
If everything turns out ok with it disconnected you can test it at the end. (The Data Link Connector is the OBD II conncetor located by the coin holder, in front of the gearchange).
Good luck!
102 views
Usually answered in minutes!
×