Purschased a new rear bumper cover (corner sliver) from my local Toyota dealer. Need instructions on installation. I have 5 new clips. How do I get the old cap off without damageing what it is mounted too? When asked for help from the parts guy he said he never replaced one but it should be easy. Need help.

Question edited for clarity.
Question moved to model category.

Assistance installing a retainer for bumper filler

Tacoma World https://www.tacomaworld.com > threads > assistance-i...

Dec 30, 2020 - A couple of weeks ago, I removed most of the front end to do three things. Repaint the lower valance (faded) :thumbsup: tackle some rust ...

Front Bumper Filler Install Problems - Tacoma World
Nov 22, 2011
Headlight Filler/Bumper Filler Clips? Are these it?
Dec 7, 2017
2012 TACOMA FRONT END CONVERSION RG11 ' Page 10
Sep 1, 2013
Another bumper filler question ' Tacoma World
Dec 15, 2015
More results from www.tacomaworld.com

How do I install the retainer for a front bumper filler on a

Fixya https://www.fixya.com > ... > Cars & Trucks > Toyota
5 hours ago - Remove the front bumper cover. Remove the tool box and the luggage compartment trim (carpet). Remove the 2 bolts and the nut. ... To install:.

Toyota Tacoma Retainer, front bumper filler, no.3

Toyota Parts Direct https://www.toyotapartsdirect.ca > Toyota__Tacoma
RETAINER, FRONT BUMPER FILLER, No.3. This Fits Your Toyota Tacoma. Part Number: 5252335020. Supersession(s): 52523-35020. RETAINER. Fits Tacoma (1995 - 2001)
Rating: 4.6 · ‎1,922 reviews · ‎$3.58

..

2000 Toyota Sienna rear Bumper cover replacement (1998 ...

? 3:40
https://www.youtube.com/watch?v=AY1BBdg3q74
Sep 20, 2013 - Uploaded by SergSpace
2000 Toyota Sienna rear Bumper cover replacement (1998-2003) .... Automotive Bumper Repair Specialist- How to repairyour plastic bumper cover ... Toyota Sienna Rear Shock Installation 2003, 2004, 2005, 2006 - Duration: ... 2015 Toyota Sienna XLE - Duration: 28:13. by MikesCarInfo 35,234 views.

Fixing My Mom's Prius: Loose Rear Bumper Cover - YouTube

I changed my 2001 Toyota Highlander headlights recently. First, remove the grille. There is one screw in the center which will require a loonng Phillips screwdriver to reach it, down behind the grille, right in the center. Then remove the four plastic clips at the top by prying them up with a small flathead screwdriver. The bottom just pulls forward. Important: Now go to each side of the car, and in front of each fender well, there is one clip that holds the bumper cover on. Pull the top corner of the bumper cover toward you to release the clips, one on each side, at the top corner, along the front of each fender well where the bumper cover meets the fender. The bumper cover can now be loosened along the top without entirely removing it. It just pulls forward. Inspect the underside of the bumper cover for broken clips and replace as necessary. Now remove the two bolts that hold down each headlight at the top. Disconnect the wiring and bulbs and wiggle the old headlights out. Install the new ones and reverse the process. If your AC isn't blowing cold, check the condenser for leaks before you reinstall the grille. A new aftermarket condenser/filter dryer is easy to install by removing the battery and tilting the radiator back to get the condenser out. A replacement only costs $75 and can be swapped out in one half hour with a few metric sockets. Then you will need to recharge the AC system with R-134a, which is easy. Just buy a R-134a kit with hose at Autozone and follow the directions. $50 Replacement fog lights are only $52/pair for aftermarket. You may consider replacing those as well. They have a strange installation with clips and you will need to pry/bop them forward, not remove them from the back. They are aggravating to replace but not technically difficult.

Hi.

Here you go:

1 - Remove one screw at each side's fender:



2 Remove two screws and clips at the back.


3 Pull out the bumper.

4 If needed remove screws holding spoiler support




5 Perform operations in reverse order to reassemble

How To Install Replace Remove Rear Bumper Cover Honda Civic 01-05

1. Locate the bolts holding the bumper cover in place. Use a socket wrench to remove the bolts, allowing you to pull the cover down. Then take off the bolts securing the headlight assembly and pull out the entire assembly from the car.
2. Squeeze the retaining clip on the washer hose with a pair of pliers and pull it back, then pull the hose off. Next, unplug the electrical connector.
3.Unbolt the headlight washer motor with your socket wrench to gain access to the bulb. Pull the bulb straight out and take it to a Jaguar dealer or the local auto-parts shop to purchase a replacement bulb.
4.Reassemble the light assembly in the reverse order. Plug in the new bulb, re-bolt the washer motor, plug in the electrical cord and reattach the hose and retaining clip. Finally, re-bolt the headlight assembly and the bumper cover.
5.Turn the car on and switch the lights on to test the newly installed bulb.

it's called a FILLER piece. I can be ordered at dealer or a local junk yard. Just replaced one , cost for part was $15 used.

Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

try this link for the bumper cover.. How to install front bumper cover on 2002 Toyota Google Search .
or this link..
How to install front passenger side splash gaurd 2002 Toyota Google Search

there is a trim panel on top of rear bumper if you look underneath there are clips that go through metal bumper also there are 4 plastic fasteners that will need to be replaced after removing best to get clips at dealer cheap enough hope this helps ya