Toyota matrix 2005 emission control system incorrect purge flow po441

code p0440 refers to evaporative emission (EVAP) system--malfunction=== causes --hose connections --intake leak--EVAP canister purge valve
code po441 refers to EVAP --incorrect flow detected==causes the same as for po440
code po446 refers to EVAP system vent control --circuit malfunction===causes --wiring---EVAP can purge valve--ECM
generally I would replace the purge valve as it is common to all codes

PO441--- Evaporative Emission Control System
Incorrect Purge Flow

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f80380329#hd1-1-28 Here is what is listed for problems,couldn't find codePO446,click on link to view.

NOPE CANT ERASE CODES UNTIL THE PROBLEM IS FIXED OR THE SERVICE ENGINE LIGHT SOON WILL STAY ON. CODE PO441 - EVAPORATIVE EMISSION EVAP SYSTEM INCORRECT FLOW DETECTED.CHECK INTAKE VACUUM HOSE CONNECTIONS AT THE EVAP CANISTER PURGE VALVE.IF ALL IS GOOD.THE EVAP CANISTER PURGE VALVE COULD BE BAD. CODE PO 442 - EVAPORATIVE EMISSION EVAP SYSTEM SMALL LEAK DETECTED. EVAPORATIVE EMISSION SYSTEM LARGE LEAK DETECTED FUEL CAP LOOSE OR OFF MISSING. CODE PO 446 - EVAPORATIVE EMISSION EVAP SYSTEM VENT CONTROL CIRCUIT MALFUNCTION.

Hi there osborne_shay,

Those codes refer to a problem with the drive train in your Avalon. Here is what the codes mean.


PO441-Evaporated Emission Control System / Incorrect Purge Flow
PO402-Excessive gas flow through the EGR valve

The cause for these issues are either that the components are faulty or they just need to be cleaned.

P0441 Evaporative Emission Control System Incorrect Purge Flow
OBD-II Trouble Code Technical Description

Evaporative Emission Control System Incorrect Purge Flow
What does that mean?

This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.
Symptoms

Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light.
Causes

A code P0441 could mean one or more of the following has happened:

* Bad vacuum switch
* Broken or damaged EVAP line or canister
* Open in PCM purge command circuit
* Open or short in Voltage feed circuit to Purge Solenoid
* Faulty purge solenoid
* Restriction in EVAP solenoid, line or canister
* Corrosion or resistance in purge connector
* Bad PCM

Possible Solutions

With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

* Common Chrysler fix - Replace Leak Detection Pump / LDP
* Repair damaged EVAP lines or canister
* Repair open or short in voltage feed circuit to Purge Solenoid
* Repair open in PCM purge command circuit
* Replace purge Solenoid
* Replace vacuum switch
* Repair restriction in Evap line or canister or soleniod
* Repair resistance in purge connector
* Replace PCM
THIS IS LIKELY FROM TOPPING OFF THE TANK EACH TIME YOU FUEL UP



P0455 is similar:

Technical Description

Evaporative Emission Control System Leak Detected (no purge flow or large leak)
What does that mean?

This indicates a fuel vapor leak or lack of purge flow in the EVAP control system. It means a large leak has been detected. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.
Symptoms

You likely won't notice any drivability problems.
Causes

A code p0455 most likely means one or more of the following has happened:

* A loose or improperly affixed gas cap
* A non-conforming gas cap (i.e. not factory/original brand)
* Other leak or damaged piece in EVAP system

Possible Solutions

With a p0455, the most common repair is to:

* Remove and reinstall the gas cap, have AutoZone clear the codes, and drive for a day and see if the codes come back.
* Otherwise, replace the gas cap, and/or
* Inspect the EVAP system for cuts/holes in tubes/hoses (you may hear a vacuum noise or smell fuel), repair if necessary

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

The EVAP cannister is part of the emissions system. Excess exhaust runs thru it-purge flow is when it is released. Check all the vacuum lines going to it. I don't you will find a parts listing for a purge flow valve or vent or solenoid. Your light will probably come on again shortly.

P0420 is catalyst system efficiency below threshold (bank 1)

P0440 is evaporative emission control system malfunction

P0441 is evaporative emission control system incorrect purge flow

These codes are all for the Evaporative Emissions System.

P0440- Evaporative emissions system fault- just saying there's something wrong with the system.

P0441- Evaporative emissions system- Incorrect purge flow- saying that the system isn't purging the raw fuel vapors (hydrocarbons- HC) as well as it should.

P0446- Evaporative emissions system- Control valve circuit low- there is a valve, usually located on the charcoal canister at the rear of the vehicle, that opens to allow fresh air to enter the evaporative emissions system as the engine vacuum purges the fuel vapors from the charcoal canister and closes when purge is not needed to prevent leakage of those fuel vapors to the atmosphere (HC is a greenhouse gas and is regulated as such by the fed gov't).

Given that you have the incorrect purge flow code and the control valve code together, my bet is that the vent control valve has failed (causing the P0446) and is not opening to allow fresh air into the system to displace the air from within the system that is being pulled to the engine. Since you have no fresh air entering the system, the engine will pull a vacuum on the system instead of the vapors "flowing" into the engine (causing the P0441).


I hope that this is helpful to you!!!


ASE Master Technician with L1 and X1 Certifications; Nissan Scope Technician; Chrysler Level 3 Silver Technician- 12+ years experience.

Look, that code means:
P0441 - Evap emission control system Incorrect purge flow

so try to replace the emission control.